Ultrasonic UP3218 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 272

background image

Property of Ultrasonic Power Corporation -

© 2018

Publication #181114

47

3. Inspection and Maintenance

3.1. General

The  maintenance  described  in  this  section  should  be  performed  at  best  intervals
determined  by  the  usage  of  the  equipment,  unless  otherwise  indicated.  Should  a
problem occur when operating the unit, refer to Section 4, Troubleshooting.  If a policy
requires for calibration of the unit, the generators would be the only calibrated items that
UPC recommends calibrating. They may be sent back to Ultrasonic Power Corporation
for calibration on an annual basis.  Please request an RMA number before shipping the
generators back to the manufacturer.

3.2. PERFORMANCE VERIFICATION

1. Check installation requirements against specifications in Section 1.

Also:

a.  Inspect overall unit for signs of damage or misaligned parts.
b.  If applicable, make sure leveling feet are adjusted to fit the floor.
c.  If  applicable,  make  sure  the  castors  are  locked  in  place  to  prevent

movement of system during operation.

d. Be sure all side panels are in place on the system.

NOTE: All side panels must be installed prior to operation to allow for

proper airflow to the system. This also protects the operator from potential

shock.

2. Check input voltage at the wall receptacle. The voltage at the wall

receptacle must be the same rating for the system for the system to
operate properly. Make sure system is grounded properly or erratic
operation may occur with optional Sonic Touch control panel.

Caution: Incorrect voltage can damage the generator. Do not
proceed unless the above voltage readings are obtained. Contact the
proper authority about necessary changes at the wall receptacle.

3. Enable the power switches for each sub-system to check their operability.

a. ULTRASONICS- Enable the ULTRASONICS power switch. Rotate the

power intensity control (PIC) clockwise to increase the cleaning action.
Sound from transducers should increase/ decrease and you should
visually see ripples in the liquid.

«
...
45
46
47
48
49
...
»

Содержание UP3218

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UP3218

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

Бренд: Panasonic Страницы: 174

Бренд: SAMCHULLY Страницы: 48

Бренд: Raymarine Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды