Ultrasonic UP3218 Скачать руководство пользователя страница 72

Страница: 72 / 272

Property of Ultrasonic Power Corporation -

Publication #181114

4. Remove access panel of machine.

5. Check for plumbing for leaks.

6. Inspect pump for damage and/or loose

wires.

7. Turn pre-strainer valve to "OFF" position.

Unscrew

transparent

pre-strainer

and

remove contaminants from mesh screen.

Return screen to pre-strainer. Ensure

washer is seated properly. Hand-tighten pre-strainer back in place. Return pre-

strainer valve to "ON" position.

8. Reattach access panel and return filter valve to desired position.

NOTE:

If damage is visible at any of these steps, contact Ultrasonic Power Corporation

service department for repair or replacement.

Filter

Housing

Pre-Strainer

Содержание UP3218

















































































































































































































































































Результаты поиска

Содержание UP3218

Отзывы:

Похожие инструкции для UP3218

Бренды по названию

Популярные бренды

Ultrasonic UP3218, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание UP3218

Отзывы:

Похожие инструкции для UP3218

Бренды по названию

Популярные бренды