Ublox MPCI-L2 series страница 143 Скачать руководство пользователя | Manualshive

Страница: 143 / 158

background image

TOBY-L2 and MPCI-L2 series - System Integration Manual

UBX-13004618 - R07

Advance Information

Approvals

Page 143 of 158

4.2.3

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by u-blox could void the user's authority to operate the equipment.

Manufacturers of mobile or fixed devices incorporating the TOBY-L2 and MPCI-L2 series
modules are authorized to use the FCC Grants and Industry Canada Certificates of the TOBY-L2
series modules for their own final products according to the conditions referenced in the
certificates.

The FCC Label shall in the above case be visible from the outside, or the host device shall bear a
second label stating:
"Contains FCC ID: XPYTOBYL200" resp.
"Contains FCC ID: XPYTOBYL201" resp.
"Contains FCC ID: XPYTOBYL210" resp.
"Contains FCC ID: XPYTOBYL280" resp.

The IC Label shall in the above case be visible from the outside, or the host device shall bear a
second label stating:
"Contains IC: 8595A-TOBYL200" resp.
"Contains IC: 8595A-TOBYL201" resp.
"Contains IC: 8595A-TOBYL210" resp.
"Contains IC: 8595A-TOBYL280" resp.

Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian CAN ICES-3(B) / NMB-3(B) and RSS-210.
Operation is subject to the following two conditions:

o

this device may not cause interference

o

this device must accept any interference, including interference that may cause undesired
operation of the device

Radio Frequency (RF) Exposure Information
The  radiated  output  power  of  the  u-blox  Cellular  Module  is  below  the  Industry  Canada  (IC)
radio frequency exposure limits. The u-blox Cellular Module should be used in such a manner
such that the potential for human contact during normal operation is minimized.
This  device  has  been  evaluated  and  shown  compliant  with  the  IC  RF  Exposure  limits  under
mobile exposure conditions (antennas are greater than 20 cm from a person's body).
This device has been certified for use in Canada. Status of the listing in the Industry Canada’s
REL (Radio Equipment List) can be found at the following web address:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng
Additional  Canadian  information  on  RF  exposure  also  can  be  found  at  the  following  web
address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

IMPORTANT: Manufacturers of portable applications incorporating the TOBY-L2 and MPCI-L2
series modules are required to have their final product certified and apply for their own FCC
Grant and Industry Canada Certificate related to the specific portable device. This is mandatory
to meet the SAR requirements for portable devices.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

«
...
141
142
143
144
145
...
»

Содержание MPCI-L2 series































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPCI-L2 series

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: IBM Страницы: 105

Бренд: Quectel Страницы: 23

Бренд: Quectel Страницы: 79

Бренд: Calsense Страницы: 74

ACTIVE DRIVER M/M 1.1

Бренд: DAB Страницы: 10

Бренд: d&b audiotechnik Страницы: 3

ACTIVE DRIVER M/M 1.1

Бренд: DAB PUMPS Страницы: 38

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

Бренд: Magellan Страницы: 2

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: POLA Страницы: 2

Бренд: Quantum Страницы: 20

Бренд: Festo Страницы: 87

Бренд: Fagor Страницы: 8

Бренд: National Instruments Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды