Ublox MPCI-L2 series страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 158

background image

TOBY-L2 and MPCI-L2 series - System Integration Manual

UBX-13004618 - R07

Page 2 of 158

Document Information

Title

TOBY-L2 and MPCI-L2 series

Subtitle

LTE/DC-HSPA+/EGPRS modules

Document type

System Integration Manual

Document number

UBX-13004618

Revision and date

R07

29-May-2015

Document status

Advance Information

Document status explanation

Objective Specification

Document contains target values. Revised and supplementary data will be published later.

Advance Information

Document contains data based on early testing. Revised and supplementary data will be published later.

Early Production Information

Document contains data from product verification. Revised and supplementary data may be published later.

Production Information

Document contains the final product specification.

This document applies to the following products:

Name

Type number

Modem version

Application version

PCN / IN

TOBY-L200

TOBY-L200-00S-00

09.71

A01.15

UBX-14044437

TOBY-L200-50S-00

09.71

A01.57

UBX-15004131

TOBY-L201

TOBY-L201-01S-00

09.87

A01.01

UBX-15016217

TOBY-L210

TOBY-L210-00S-00

09.71

A01.15

UBX-14044437

TOBY-L210-50S-00

09.71

A01.57

UBX-15004131

TOBY-L280

TOBY-L280-00S-00

09.90

A01.02

UBX-15016802

MPCI-L200

MPCI-L200-00S-00

09.71

A01.15

UBX-14044437

MPCI-L210

MPCI-L210-00S-00

09.71

A01.15

UBX-14044437

u-blox reserves all rights to this document and the information contained herein. Products, names, logos and designs described herein may in
whole or in part be subject to intellectual property rights. Reproduction, use, modification or disclosure to third parties of this document or
any part thereof without the express permission of u-blox is strictly prohibited.
The information contained herein is provided “as is” and u-blox assumes no liability for the use of the information. No warranty, either
express or implied, is given, including but not limited, with respect to the accuracy, correctness, reliability and fitness for a particular purpose
of the information. This document may be revised by u-blox at any time. For most recent documents, please visit www.u-blox.com.
Copyright © 2014, u-blox AG
u-blox

®

is a registered trademark of u-blox Holding AG in the EU and other countries. PCI, PCI Express, PCIe, and PCI-SIG are trademarks or

registered trademarks of PCI-SIG. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries. ARM

®

is a registered trademark of ARM Limited in the EU and other countries. All other registered

trademarks or trademarks mentioned in this document are property of their respective owners.

«
1
2
3
4
...
»

Содержание MPCI-L2 series































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPCI-L2 series

Бренд: wattio Страницы: 20

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: Sole Diesel Страницы: 8

Бренд: Garmin Страницы: 12

Бренд: C3 Custom Coolers Страницы: 16

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

Бренд: National Instruments Страницы: 22

Бренд: Maker Factory Страницы: 3

CONPAL NCB-8C-SR

Бренд: Nabtesco Страницы: 24

Бренд: SAFERA Страницы: 32

iMO-LEARN - MDM

Бренд: i3-TECHNOLOGIES Страницы: 2

ROC 1407 - CODE

Бренд: THOMSON Страницы: 2

Бренд: Arcus Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды