UAZ UAZ-220695 Скачать руководство пользователя | Manualshive

Страница: 20 / 90

background image

20

Description

UAZ vehicle models

Driveline

Open type, consisting of two shafts. Each shaft has two cardan-joint with a cross on needle bearings

Front and rear drive axles:

axle type

Single-stage, driven

final drive gear ratio, axle differential

4.625 Cone-shaped with 4 satellites

steering knuckle pivots of the front axle

Ball-type constant-velocity joints

1)

Installation of a power take-off box shall be agreed with UAZ LLC as appropriate

Chassis

Description

UAZ vehicle models

374195, 390995, 330365, 390945

396295,220695

Suspension:

suspension type

On four longitudinal semielliptical springs with (or without) anti-roll
bar in the front suspension

On four longitudinal semielliptical springs with anti-roll bar in the
front suspension; rear springs with mounts

shock absorbers

Four pieces, hydraulic, telescopic bilateral, rear: hydraulic, front:
hydraulic or hydro-pneumatic (if equipped with anti-roll bar

Four telescopic, bilateral, front: hydro-pneumatic, rear: hydraulic

Wheels and tires:

One-piece rim disks 61/2Jx16H2, with 225/75R16 radial tubeless tires. Wheel fastening - by five nuts.

The spare wheel is made of steel, fitted with the same size tire as the wheels for normal operation. On some vehicles, the spare wheel can
be equipped with a tire 225/70R16, used as a spare wheel for temporary use.

The spare wheel is attached to the holder with one nut

Control system

Description

UAZ vehicle models

Steering mechanism type

Screw-ball nut-rack-sector with power steering

Brakes:

service brake type

With disc brakes on the front wheels and drum brakes on the rear wheels with ABS or pressure regulator without ABS

working brake actuator type

Hydraulic with vacuum booster, separate for front and rear wheels

parking brake type

Drum with internal pads

parking brake actuator type

Mechanical

Electrical equipment

Description

UAZ vehicle models

Wiring system

Single-wire, negative pole is connected to vehicle ground

Electrical system voltage (rated), V

12

Generator

5122.3771 (14B 80A OOO Pramo-Elektro); 3212.3771-10 (14B 90A OAO BATE for medical service cars -
5122.3771.000-30 (14B 120A OOO Pramo-Elektro); 32112.3771 (14B 110A OAO BATE)

Battery

6ST-66A or 6ST-66A with ventilation pipe

«
...
18
19
20
21
22
...
»

Содержание UAZ-220695



























































































Отзывы:

Нет отзывов

Похожие инструкции для UAZ-220695

Бренд: Happy Orange Страницы: 2

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Alpine Страницы: 69

Бренд: Allen Sports Страницы: 2

Бренд: Wagan Страницы: 8

Бренд: Thermo King Страницы: 2

Gold Cruuse Cruisecontrol GC90

Бренд: John Gold Страницы: 24

Бренд: Whispbar Страницы: 14

Бренд: StowAway 2 Страницы: 2

Grand Cherokee SRT 2019

Бренд: Jeep Страницы: 656

Security Cage Kit

Бренд: Toro Страницы: 8

Бренд: Toyota Страницы: 779

1953 Traction Avant

Бренд: CITROEN Страницы: 26

Бренд: v.link Страницы: 19

Бренд: Motoalliance Страницы: 4

Бренд: Tactik Страницы: 4

Бренд: banks Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды