UAZ UAZ-220695, Руководство по эксплуатации

Страница: 24 / 90

24
- always wear thick canvas gloves when working with the rope;
- in order to avoid injuries, it is prohibited to keep the moving cable at a distance of less than 0.5 m from the
vehicle's bumper;
- in order to avoid injuries when winding the cable on the winch drum, do not correct the turns by hand;
- it is necessary to control the winding and condition of the cable. The cable must fit tightly with turn touching along
the entire length of the winch drum. Wire breaks in the strands, kinks, knots and cable squeezing are not allowed;
- do not operate the winch with a damaged wire rope;
- when operating the winch with a load on the cable, it is recommended to put a cable damper or a soft object
(jacket, sleeping bag, etc.) on a cable to arrest its separation in the event of cable brake. It is forbidden to stay close to the
tensioned cable, on the tensioned cable, as well as step over the tensioned cable;
- it is forbidden to use the winch cable as a towing cable, this leads to the failure of the winch;
- it is not allowed to stay in front of the vehicle being moved by the winch. You must be either in the vehicle cab or on
the side, outside the track of the vehicle.
- in the event of an emergency situation associated with the winch, when the cable is being wound on the drum
without control, it is necessary to immediately de-
energize the winch by removing the power cable lug from the “+”
terminal of the battery;
- responsibility for the safe operation of the winch, prevention of damage to the vehicle and injuries is born solely by
the winch operator.
22. When carrying out maintenance and repair of the vehicle, it is necessary to fulfill the following requirements:
- prior to begin the work, check the serviceability of the tool and accessories, tidy up the working clothes: fasten the
cuffs, tuck in the clothes so that there are no hanging ends, hide the hair under a tight-fitting headwear;
- when carrying out any type of work, the vehicle must be reliably braked;
- do not carry out maintenance and repair of the vehicle when the engine is running, except for certain types of work
which require engine start, concurrently particular caution shall be taken;
- do not allow dangerous approach of hands, parts of clothes, tools to moving drive belts, pulleys, etc.;
- fuel supply system downstream of the fuel pump is under pressure with the engine running, therefore it is not
allowed to perform maintenance (for example, tighten the connections) or repair system components, while the engine is
running or immediately after it stops;
- exercise caution when opening the radiator cap of the engine cooling system in order to avoid steam burns;
- the fuel tanks must be removed before carrying out any arc welding operations;
- observe the rules of fire safety;
23. Waste oils and special fluids must be collected and recycled or disposed.
24. A number of safety requirements are given in detail in the relevant sections of this manual.
WARNINGS
1.
During the initial period of operation, strictly follow all recommendations specified in the section “Running in a
new vehicle”.
2. Do not start the vehicle with a cold engine. Do not allow high speed of crankshaft after starting a cold engine.
For the purpose to accelerate the engine heating, never perform it with a higher frequency of the crankshaft
rotation.
To prevent difficulties during engine start, stri
ctly follow the instructions in the “Starting Engine” section.
3. If there are distinct noises and knocks in a running engine, it is necessary to find out the reason of their
occurrence, and the vehicle shall not be operated until the fault is eliminated.
3.1 After starting the cold engine, knocks in the valve hydraulic plunger are possible, which shall disappear as the
engine warms up to a coolant temperature of 80-
90 ° C, but no more than 30 minutes after reaching the specified
temperature. If the knocks fail to disappear, check the oil supply to the hydraulic pushers or replace the defective
hydraulic pushers.
4. Engage the reverse gear in the gearbox and reduction gearing in the transfer case only after the complete stop of
the vehicle.
5. When driving on dry hard roads, the front axle must be disengaged.
Do not engage the front axle when driving a vehicle with small turning radii.
6.
In the event of failure of one of the brake system circuits, the brake pedal travel increases and braking
performance decreases.
7. Never remove the tips of the spark plugs with the engine running and check the sparking discharge by means of a
ground/frame contact.
8. Prevent contact of acids, soda solutions, brake fluid, antifreeze, fuel and lubricants with painted surface of the
body, wheels, rubber parts.
9. Do not allow shock loads on the vehicle chassis. In case of front wheels hitting hard, carefully inspect all the
components of the front axle, steering linkages, steering gear and repair any defects found.
10. The differential lock of rear axle (depending on package) ensures a rigid connection between the left and right
wheels, eliminating their separate slipping, which in some cases improves the vehicle’s off
-road performance, but impairs
its driving and stability, and additionally loads transmission parts. For safety reasons, the operating the differential in the