UAZ UAZ-220695 страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 90

background image

18

TECHNICAL DATA

General data

Description

UAZ vehicle models

374195(-05)

396295

220695(-04)

390995(-04)

330365

390945

Vehicle dimensions

1)

Shown in Fig. 1.1 - 1.12

Vehicle type

Off-road, two-axle, type 4x4

Number of seats

2 (5)

4+1

9+1 (8+1)

5 (7)

2

5

Passenger capacity

-

4

9 (8)

-

-

-

Weight of cargo transported in the cargo compartment, kg, not
more

—

—

—

475 (410)

—

—

Weight of cargo transported on the platform, not more than

—

—

—

—

1150

700

Technically permissible maximum vehicle weight, kg

2730 (2845)

2880

2880

2830

3070

3070

Distribution Technically max permissible weight distributed by
axles, kg:

on front axle

1300 (1350)

1440

1440

1360

1435

1435

on rear axle

1430 (1495)

1440

1440

1470

1635

1635

Unladen weight of car

2)

, kg

1805 (1920)

2000

2015 (2005)

1890 (1920)

1845

1995

Distribution of unladen weight by axles, kg:

on front axle

1085 (1160)

1180

1195 (1185)

1135 (1155)

1180

1220

on rear axle

720 (760)

820

820 (820)

755 (765)

665

775

Max. gross weight of towed trailer:

without brakes

750

3)

-

-

-(750

3)

)

-

750

3)

Minimum turning radius on the centerline of the front outer
(relative to the turning center) wheel trace, m, max.

6.3

7.0

Minimum outer turning radius as to the front bumper point, the
farthest from the turning center, m, max.

6.8

7.5

Max. grade climbed by vehicle with the vehicle, degrees

30

The greatest depth of a ford, m

0.5

Maximum speed, km/h

127

115

Fuel consumption, L/100 km, when driving at 60 km/h

9,0

4)

9,6

4)

Fuel consumption, L/100 km, when driving at 80 km/h

11,2

4)

12,4

4)

1)

Dimensions are averaged, given for reference and may vary depending on the operating conditions of the installed tires, their condition and air pressure, vehicle load, suspension condition, etc.

2)

With fuel, tools, extra equipment, spare tire and driver

3)

A trailer may only be towed with a ball-type tow hitch that has been certified as part of a haul train in the prescribed manner.

4)

Fuel consumption is used to determine the technical condition of the vehicle and shall not be regarded as the operational standard. Reliability of measurements of fuel consumption is ensu red only during special tests in strict

accordance with the requirements of GOST R 54810-2011 when the vehicle reaches a total mileage of 9000-10000 km.

«
...
16
17
18
19
20
...
»

Содержание UAZ-220695



























































































Отзывы:

Нет отзывов

Похожие инструкции для UAZ-220695

Бренд: AAMP of America Страницы: 6

Бренд: Daihatsu Страницы: 43

Бренд: Dakota Digital Страницы: 2

Бренд: Dakota Digital Страницы: 7

Бренд: Kathrein Страницы: 7

Бренд: Aries Страницы: 3

Бренд: Alpine Страницы: 69

Бренд: Allen Sports Страницы: 2

Бренд: Saab Страницы: 445

Бренд: Yakima Страницы: 21

Бренд: tams elektronik Страницы: 19

Бренд: EUFAB Страницы: 16

Бренд: Paser Страницы: 2

Бренд: Xblitz Страницы: 56

Бренд: Billien Страницы: 2

Бренд: Lexus Страницы: 28

PRIME DESIGN VRR3-FT21G-ST

Бренд: Safe Fleet Страницы: 12

2013 2500 Big Horn

Бренд: RAM Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды