U.S. Boiler Company ALTA ALTAC-136B Скачать руководство пользователя

Страница: 41 / 104

110327-07 - 2/23

ALTA

Combi Installation, Operating & Service Instructions

UTION

Component and P

roper

ty Dama

• Excessive heat fr

om soldering could damage gaskets

at connection between DHW adapters and boiler

. Solder

connections to DHW adapters befor

e installing gaskets.

• DHW pr

essur

e r

elief valve (and when appr

opriate-

expansion tank) r

equir

ed to pr

otect inter

nal boiler

components. Failur

e to addr

ess these items could r

esult in

component failur

e and pr

oper

ty damage.

Domestic Water Piping

(continued)

TICE

: Heating System piping omitted for clarity

TICE

: Installer is r

esponsible for piping configurations to pr

ovide

oper flow rates and meet local codes.

ANGER

Scald Hazar

Under cer

tain conditions this boiler can

deliver domestic hot water (DHW) at temperatur

es in excess

of DHW setpoint in boiler contr

ol. A field supplied ASSE

1070 listed anti-scald valve is r

equir

ed as par

t of this boiler’

installation when DHW r

ecir

culation is used.

Figur

e 1

1-3:

DHW Piping with R

ecir

culation

TICE:

Additional wiring and contr

ol settings r

equir

ed for

DHW r

ecir

culation:

•

Connect r

ecir

culation pump to "Aux Pump" ter

minals per

Figur

e 13-2.

•

Connect jumper

, time of day clock or momentar

y push

button to "Aux T'Stat" ter

minals per Figur

e 13-3.

•

Secur

e r

ecir

culation temp sensor close to boiler on cold

water line.

•

Connect r

ecir

culation temperatur

e sensor to "Header Sensor"

ter

minals per Figur

e 13-3.

•

Change

A02

Recir

c (Comfor

t) Mode to 'ON' See T

able 16-11.

• Change

S05

(Auxiliar

y Ther

mostat Input Select) to '0'

(Recir

culation Enable). See T

able 16-13

• Change

P03

(Auxiliar

y Pump Output Select) to '1'

(Recir

culation Pump) See T

able 16-15.

TICE:

ater

filter

event

scale

str

ongly

ecommended on the potable cold water supply line to

minimize sediment build up and loss of per

for

mance of

the plate heat exchanger

DHW

Pressure

Relief Valve

Drain

Valve

Buffer Tank

(2-6 Gal.)

(optional)

Drain

Valve

ASSE 1070 Listed

Anti-Scald Valve

(required)

Cold Water Supply

Recirc. Temp. Sensor

(P/N 108703-01)

Expansion Tank

(Req'd if cold water supply line

has check valve)

Flow Check

Valve

Recirc.

Pump

Hot Water

To Fixtures

*Supplied with boiler

DHW Strainer*

(inside boiler)

DHW Flow Limiter*

(inside boiler)

DHW Adapters*

(G 1/2" to 3/4" sweat)

Water Filter

Aqua Pure AP430SS or equivalent

(highly recommended)

Detail A

(Scale 1 : 4)

Cold Water Supply

Hot Water (From Boiler)

Hot Water To Fixtures

Содержание ALTA ALTAC-136B









































































































Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Похожие инструкции для ALTA ALTAC-136B

Бренды по названию

Популярные бренды

U.S. Boiler Company ALTA ALTAC-136B, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Похожие инструкции для ALTA ALTAC-136B

Бренды по названию

Популярные бренды