U.S. Boiler Company ALTA ALTAC-136B Скачать руководство пользователя страница 64

Страница: 64 / 104

ALTA

Combi Installation, Operating & Service Instructions

110327-07 - 2/23

1. Boiler Control

Control simultaneously modulates blower speed

and gas valve position to control firing rate and

sequences up to three pumps and a 3 way valve

to respond to DHW and CH demands.

2. Flame Supervision/Air-Fuel Ratio Control

Control is a "Gas-Adaptive system" that regulates

air and gas flow mixture by measuring flame

ionization and adjusting gas valve to achieve

target air fuel ratio. This eliminates need to make

throttle screw or offset adjustments. This system is

self-calibrating and continuously maintains air fuel

ratio at desired value.

3. Domestic Hot Water

DHW demand is detected by a DHW flow sensor.

When a DHW draw greater than 0.5 gpm is

detected, control diverts all boiler water flow

through plate heat exchanger, starts boiler pump

and modulates firing rate based on measured

DHW temperature and DHW set-point. When there

is a DHW demand, system pump will be turned

off, boiler services only DHW. Priority protection

is provided to ensure heating system is also

serviced.

4. DHW Recirculation

When "Recirculation (Comfort) Mode" is selected

(from Quick Menu

) a recirculation sensor and

auxiliary thermostat input are monitored and a

recirculation pump is controlled via aux pump

terminals in order to maintain a warm DHW loop.

Recirculation can reduce time needed for hot

water to appear at a fixture. Refer to internal

wiring diagrams Figures 20-1 and 20-2 for

recirculation pump and sensor connections and

piping diagram Figure 11-3 for recommended

piping layout.

5. Central Heat

CH demand is detected by a heating thermostat

call for heat. When CH demand is detected,

control diverts all boiler water to CH zones, starts

boiler pump and modulates firing rate based on

measured supply sensor and CH setpoint. When

DHW recirculation is not used control can accept

a second heating thermostat wired to the Aux

T'stat input. CH demands have separate setpoint

and maximum modulation rates.

6. Sensorless Reset

Control system monitors recent firing rate and

burner cycle data to infer current building heat

loss. Target supply water temperature is then

adjusted to match this heat load. No outdoor

sensor mounting or wiring is required. Boost

feature increases operating temperature setpoint

by 10°F (5.6°C) every 20 minutes CH demand

is not satisfied. This process will continue until

heat demand is satisfied (indoor air is at desired

temperature), or CH setpoint is reached. Once

heat demand is satisfied, operating setpoint

reverts to value determined by the Outdoor Reset

settings.

7. Pump Exercise

Connected pumps are automatically run for a 20

second exercise period after not being used for

longer than 7 days. This helps prevent pump rotor

seizing.

8. Pump Air Elimination (Pump Purge)

Pump purge is entered when power is cycled or

when there has been an over temperature hold.

During this state boiler pump and three way

valve cycle in sequence for two minutes to help

remove air from boiler water piping. This may be
interrupted by pressing the

reset

button

9. Built-in Safety Control

Control includes functions designed to ensure

safe and reliable operation. In addition to flame

supervision, control monitors supply water

temperature, differential water temperature, and

flue temperature safety limits. Boiler modulation

is adjusted when required to help avoid loss

of boiler operation due to exceeding limits.

Additionally, control accepts field installation of

external limits.

10. Fuel Conversion

The conversion from Natural Gas to LP Gas (or

vice versa) is made by changing gas valve setting

and a control parameter change on display.

11. Compatible with Multiple Boiler Sequencer

The control is compatible with Alta, K2WT, ASPEN

and Alpine multiple boiler sequencer peer-to-peer

networks. Control can be connected to up to eight

(8) boilers using RJ45 Ethernet cable. Alta combi

goes "on leave" from network when DHW demand

is present.

Control System Overview

The control manages all of the following boiler

functions:

Operation

(continued)

This section covers control features available via local display. For additional control features available via our App,

see Extended Features Manual available on our website or in our App.

Содержание ALTA ALTAC-136B









































































































Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Бренды по названию

Популярные бренды

U.S. Boiler Company ALTA ALTAC-136B, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Бренды по названию

Популярные бренды