U.S. Boiler Company ALTA ALTAC-136B Скачать руководство пользователя

Страница: 85 / 104

110327-07 - 2/23

ALTA

Combi Installation, Operating & Service Instructions

Troubleshooting

(continued)

Table 19-6: Detailed Fault Code (found on"

" and "

" menus)

Code

Detailed

Code

Type

Condition

H01

Warning Anti-short cycle boiler start delay, while thermostat demand present, boiler has

cycled off and restart is delayed.

H01

Warning Urgent calibration cooling delay. Boiler start delay, urgent calibration is present,

waiting for supply temperature to decrease.

H01

Hold

Flow switch is closed, boiler start is delayed waiting for flow switch to open.

H02

Hold

A safety limit is open and preventing boiler from starting.

H04
E04

H04

Hold

Supply Temperature is higher than 200°F (93°C) or (when used) preferred outlet/

flow high limit (Manual Reset Lockout Limit) (minus 10°).

E04

Lockout Supply Temperature is higher than 210°F (99°C) or (when used) preferred outlet/

flow high limit (Manual Reset Lockout Limit).

H05
E05

H05

Hold

Temperature rise between supply and return greater than 63°F (17°C).

H05

Hold

Boiler water flow switch does not detect water flow. Switch contact is "open" when it

should be "closed".

E05

Lockout Boiler water flow switch does not detect water flow. Switch contact is "open" when it

should be "closed" after 5 retries.

E05

Lockout Temperature rise between supply and return is greater than 63°F (17°C).

E05

Lockout Boiler water flow switch contact is "closed" when it should be "open".

H06
E06

H06

Hold

Flue gas sensor detected temperatures in excess of 194°F (90°C) or when used

preferred stack/flue limit (minus 10°).

E06

Lockout Flue gas sensor detected temperatures in excess of 204°F (96°C) or when used

preferred stack/flue limit.

H07
E07

H07

Hold

Return temperature higher than supply temperature.

E07

Lockout Return temperature higher than supply temperature.

H08

Hold

Shorted, opened or miswired return temperature sensor.

H09
E09

H09

Hold

Shorted, opened or miswired supply temperature sensor.

E09

Lockout Shorted, opened or miswired supply temperature sensor longer than 10 seconds.

E09

Lockout Temperature difference between dual elements too high.

H10

Warning Shorted, opened or miswired DHW temperature sensor.

H11
E11

H11

Hold

Shorted, opened or miswired Flue temperature sensor.

E11

Lockout Shorted, opened or miswired Flue temperature sensor longer than 10 seconds.

H12

Warning Shorted, opened or miswired outdoor air temperature sensor.

H13

Hold

Shorted, opened or miswired Header temperature sensor.

H14

Hold

0-10VDC Input is out of range.

H14

Hold

4-20mAdc Input is out of range.

H14

Hold

Analog Input parameter setup incorrect.

E15

Lockout The Air Pressure Switch detects airflow while fan is not running. Switch contact is

"closed" when it should be "open".

H16
E16

E16

Lockout Air proving switch does not detect air flow for more than 51 seconds.

E16

Lockout Fan standstill not reached.

H16

Hold

Fan speed is not proven during running mode.

E16

Lockout Fan speed is not proven during prepurge or post purge.

Содержание ALTA ALTAC-136B









































































































Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Похожие инструкции для ALTA ALTAC-136B

Бренды по названию

Популярные бренды

U.S. Boiler Company ALTA ALTAC-136B, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Похожие инструкции для ALTA ALTAC-136B

Бренды по названию

Популярные бренды