U.S. Boiler Company ALTA ALTAC-136B Скачать руководство пользователя

Страница: 80 / 104

ALTA

Combi Installation, Operating & Service Instructions

110327-07 - 2/23

Troubleshooting

(continued)

Code

Name

Possible Cause

Corrective Action

H06
E06

Flue High

Limit

Heat exchanger dirty.

Inspect heat exchanger and clean flue side of heat

exchanger.

Boiler over-fired.

Reduce maximum firing rate.

H07
E07

Return Temp

Higher than

Supply

Flow through boiler

reversed.

Verify correct piping and pump orientation.

Supply or return sensor

defective or not installed

properly.

Check supply and return sensors, correct installation or

replace if required.

No boiler water flow.

Verify system is purged of air and that appropriate valves

are open. Also verify pump is running and set to speed 3

(Figure 15-2). Check T5-0 A fuse (Figures 20-1 and 20-2),

replace if necessary. Replace pump if necessary.

H08

Return

Sensor Fault

Shorted or miswired return

temperature sensor.

• Check return sensor wiring, correct wiring if necessary.

• Check return sensor, refer to sensor temperature vs.

resistance (Table 19-7). Replace sensor if necessary.

H09
E09

Supply

Sensor Fault

[

] Shorted,

opened or miswired supply

temperature sensor.

• Check supply sensor wiring, correct wiring if necessary.
•

Check supply sensor, refer to sensor temperature vs.

resistance (Table 19-7). Replace sensor if necessary.

[

] Temperature difference

between dual elements too

high.

Measure resistance of each thermistor and compare,

refer to sensor temperature vs. resistance (Table 19-7).

Replace sensor if necessary.

H10

DHW Sensor

Fault

Shorted, opened or

miswired DHW temperature

sensor.

• Check DHW sensor wiring, correct wiring if necessary.

• Check DHW sensor, refer to sensor temperature vs.

resistance (Table 19-7). Replace sensor if necessary.

H11
E11

Flue Sensor

Fault

Shorted, opened or

miswired flue temperature

sensor.

• Check flue sensor wiring, correct wiring if necessary.

• Check flue sensor, refer to sensor temperature vs.

resistance (Table 19-7). Replace sensor if necessary.

H12

Outdoor Air

Sensor Fault

Shorted, opened or

miswired outdoor air

temperature sensor.

• Check outdoor air sensor wiring, correct wiring if

necessary.

• Check outdoor sensor, refer to sensor temperature vs.

resistance (Table 19-7). Replace sensor if necessary.

H13

Header Or

Recirculation

on Sensor

Fault

Shorted, opened or

miswired header or

recirculation temperature

sensor.

• Check header or recirculation sensor wiring, correct

wiring if necessary.

• Check header sensor, refer to sensor temperature vs.

resistance (Table 19-7). Replace sensor if necessary.

Recirculation (Comfort)

Mode selected and

recirculation temperature

sensor not installed.

Disable Recirculation (Comfort) Mode or install a

recirculation temperature sensor.

H14

0-10 Vdc /

4-20 mAdc

Input Fault

[

]

Shorted or miswired

0-10 Vdc / 4-20 mAdc

input.

(Feature not available with local user display.)

Check 0-10 Vdc/4-20 mAdc input wiring, correct if

necessary.

[

]

Analog input parameter

setup incorrect.

(Feature not available with local user display.)

Check and correct parameter settings.

Table 19-5: Active Fault Code and Corrective Actions (continued)

Detailed Fault Code found on "

" and "

" menus in brackets, e.g. [

Содержание ALTA ALTAC-136B









































































































Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Похожие инструкции для ALTA ALTAC-136B

Бренды по названию

Популярные бренды

U.S. Boiler Company ALTA ALTAC-136B, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Похожие инструкции для ALTA ALTAC-136B

Бренды по названию

Популярные бренды