U.S. Boiler Company ALTA ALTAC-136B Скачать руководство пользователя | Manualshive

Страница: 12 / 104

background image

12

ALTA

Combi Installation, Operating & Service Instructions

110327-07 - 2/23

4. If boiler is installed in room with other

appliances, provide adequate air for combustion

and/or ventilation in accordance with other

appliance manufacturer's instructions and

applicable code. If other appliance(s) require two

openings at least 100 in.

2

(650 cm

2

) each, no

additional openings are required for this

boiler.

Combustion Air and Venting

WARNING

Asphyxiation Hazard.

Boiler requires a special venting system

designed for positive pressure. Supplied vent

connector connects to CPVC, polypropylene,

and stainless steel venting listed in Section

7, General Venting. Failure to vent boiler in

accordance with these instructions could cause

products of combustion to enter the building

resulting in severe personal injury, death or

substantial property damage.

!

DANGER

Component Malfunction.

Outdoor combustion air must be piped directly

to boiler air connection. Ensure combustion air

does not contain contaminants and is not drawn

from an area likely to have contaminants per

Table 5-2. For example, never pipe combustion

air from areas near swimming pools or laundry

room exhaust vents. Contaminated combustion

air will damage boiler resulting in severe

personal injury, death or substantial property

damage.

!

Contaminants to avoid:

Spray cans containing chloro/fluorocarbons (CFC’s)
Permanent wave solutions
Chlorinated waxes/cleaners
Chlorine-based swimming pool chemicals
Calcium chloride used for thawing
Sodium chloride used for water softening
Refrigerant leaks
Paint or varnish removers
Hydrochloric acid/muriatic acid
Cements and glues
Antistatic fabric softeners used in clothes dryers
Chlorine-type bleaches, detergents, and cleaning

solvents found in household laundry rooms.
Adhesives used to fasten building products and

other similar products
Excessive dust and dirt

Areas likely to have contaminants:

Dry cleaning/laundry areas and establishments
Swimming pools
Metal fabrication plants
Beauty shops
Refrigeration repair shops
Photo processing plants
Auto body shops
Plastic manufacturing plants
Furniture refinishing areas and establishments
New building construction
Remodeling areas
Garages with workshops

Table 5-2: Corrosive Combustion Air

Contaminants and Sources

1. Use only vent and air piping and termination

methods listed in Section 7, General Venting. Vent

and air piping must terminate either horizontally

through a sidewall or vertically through a roof or

chase. Locate boiler so vent and air intake piping

can be routed through building and properly

terminated.

2. Ensure installation does not exceed maximum

air and vent pipe lengths and terminations

are located in acceptable location per these

instructions and all applicable local codes.

5

Locating Boiler

(continued)

«
...
10
11
12
13
14
...
»

Содержание ALTA ALTAC-136B









































































































Отзывы:

Нет отзывов

Похожие инструкции для ALTA ALTAC-136B

Бренд: RBI Страницы: 44

Бренд: Kardia Страницы: 43

Бренд: Main Страницы: 12

Бренд: Magikitch'n Страницы: 4

Бренд: Navien Страницы: 147

Бренд: Navien Страницы: 4

Бренд: Navien Страницы: 151

Бренд: Navien Страницы: 135

Бренд: Navien Страницы: 155

Бренд: Laars Страницы: 8

Бренд: M&G Страницы: 41

microGENUS 23 MFFI

Бренд: Ariston Страницы: 28

Бренд: Ideal Boilers Страницы: 8

Бренд: Fondital Страницы: 64

Бренд: Baxi Страницы: 36

Бренд: Market Forge Industries Страницы: 20

CIAO GREEN C.S.I.

Бренд: Beretta Страницы: 50

EXCLUSIVE GREEN 16 RSI

Бренд: Beretta Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды