U.S. Boiler Company ALTA ALTAC-136B Скачать руководство пользователя

Страница: 72 / 104

ALTA

Combi Installation, Operating & Service Instructions

110327-07 - 2/23

Service and Maintenance

(continued)

15.

Place boiler back into operation.

A. Replace any wiring which has been

disconnected.

B. Perform visual inspection of gas piping

to ensure no inadvertent damage to gas train

components during servicing.

C. Follow all instructions in Section 15 Start-Up

and Checkout to place boiler back in service,

including performance of combustion test.

16.

Test boiler flow switch.

A. Start with boiler in standby.

B. Either close a shut off in boiler loop or unplug

boiler pump at connecter.

C. Initiate a call for heat and confirm that boiler

shows an Active Fault (

H05

) indicating flow

switch is open.

WARNING

Component Damage.

If burner comes on with no flow through boiler,

there is a problem with flow switch. Turn boiler

off immediately. Failure to do so could result in

severe heat exchanger damage.

17.

Assure that all safety and operating controls

and components are operating properly before
placing boiler back in service

12.

Inspect hydronic system and DHW piping.

A. Look for leaks and repair if found. If system

contains antifreeze, or other additives, test

and/or maintain them as directed by additive

manufacturer.

B. Test heating system and DHW inlet water

quality to ensure they meet minimum

requirements specified in Section 15 Start-Up

and Checkout and Section 11 Domestic Water

Piping.

C. Inspect DHW flow limiter. Clean any debris/

build up, replace if necessary

D. If DHW cold water supply is equipped with

a water filter replace according to

manufacturer's recommendations.

E. Refer to Appendix B. for important information

on quality and boiler additives.

13.

Flush plate heat exchanger.

Back-flush (against normal flow) DHW loop to

remove scaling. Vinegar can be used to help

remove deposits.

14.

Inspect safety relief valve.

WARNING

Explosion Hazard.

Safety relief valves require periodic

maintenance. Refer to relief valve

manufacturer's instructions for frequency and

proper procedure. Any testing or maintenance

shall be done by a qualified installer, service

agency or gas supplier..

Содержание ALTA ALTAC-136B









































































































Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Похожие инструкции для ALTA ALTAC-136B

Бренды по названию

Популярные бренды

U.S. Boiler Company ALTA ALTAC-136B, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALTA ALTAC-136B

Отзывы:

Похожие инструкции для ALTA ALTAC-136B

Бренды по названию

Популярные бренды