background image

58   

                                                                                                                                       

103448-10- 6/18

Table 14:  Fitting and Valve Equivalent Length

Copper Fitting and Sweat Valve

Equivalent Length (Ft)

Fitting or Valve
Description

Copper Pipe or Valve Size

1

2

90° Elbow

2.5

3.0

4.0

5.5

45° Elbow

1.0

1.2

1.5

2.0

Tee (through flow)

0.5

0.6

0.8

1.0

Tee (Branch flow)

4.5

5.5

7.0

9.0

Diverter Tee (typical)

23.5

25.0

23.0

23.0

Gate Valve

0.3

0.4

0.5

0.7

Globe Valve

25.0

36.0

46.0

56.0

Angle Valve

5.3

7.8

9.4

12.5

Ball Valve (standard port)

4.3

7.0

6.6

14.0

Ball Valve (full port)

1.9

1.4

2.2

1.3

Swing Check Valve 

4.5

5.5

6.5

9.0

Flow-Check Valve 
(typical)

54.0

74.0

57.0

177.0

Butterfly Valve

2.7

2.0

2.7

4.5

Threaded Fitting and Valve Equivalent Length (Ft)

Fitting or Valve
Description

Black Threaded Pipe or

Valve Size

1

2

90° Elbow

2.6

3.5

4.0

5.2

Long Radius
Elbow (45° or 90°)

1.4

1.8

2.2

2.8

Tee (through flow)

1.8

2.3

2.7

3.5

Tee (Branch flow)

5.3

6.9

8.1

10.0

Close Return Bend

4.4

5.8

6.7

8.6

Gate Valve (full open)

0.7

0.9

1.1

1.4

Globe Valve (full open)

30.0

39.0

46.0

59.0

Angle Valve (full open)

13.0

17.0

20.0

26.0

Swing Check Valve
(full open) 

8.7

12.0

13.0

17.0

Flow-Check Valve 
(typical)

42.0

60.0

63.0

83.0

Table 14:  Fitting and Valve Equivalent 

Length (continued)

NOTE: 

 

Table 14 is provided as reference to assist in piping design and specifies equivalent length of typical piping fittings and 

  valves.

VI.  Water Piping and Trim

 (continued)

6.  Manual Reset High Limit (Required by some 

Codes)

 

 This control is required by ASME 

CSD-1

  and some other codes.  Install the high limit in 

the boiler supply piping just above the boiler 

with no intervening valves.  Set the manual 

reset high limit to 200°F.  Wire the limit per 

Figures 27 and 28 in Section VIII Electrical.

7.  Flow Control Valve (Strongly Recommended) 

 The flow control valve prevents flow through 

the system unless the circulator is operating.  

Flow control valves are used to prevent gravity 

circulation or “ghost flows” in circulator zone 

systems through zones that are not calling for 

heat.

8.  Y-strainer (Recommended) 

 A Y-strainer or 

equivalent strainer removes heating system 

debris from hydronic systems and protects 

boiler heat exchanger from fouling up. Install 

the strainer downstream of full port isolation 

valve, at the inlet side of the circulator, for easy 

service.

9.  Isolation Valves (Strongly recommended)

 – 

Isolation valves are useful when the boiler must 

be drained, as they will eliminate having to 

drain and refill the entire system.

10.  Drain Valve (Required)

 –

 Drain valve is 

packaged loose with boiler and must be 

installed in the location shown in Figure 20 

“Factory Supplied Piping and Trim Installation” 

of the Installation, Operating and Service 

Instructions.

11.  Low Water Cutoff.

  

A hot water boiler installed 

above radiation level, or as required by the 

Authority having Jurisdiction, must be provided 

with a low water cutoff device at time of boiler 

installation.

a.  Automatic Reset LWCO with harness, Part 

Number 100592-01.
•  Install as shown in Figure 21, 22, 24B or 

25B.

•  Wire using harness provided with low 

water cutoff per Figures 27 and 28.

b.  Manual Reset LWCO, Part Number 

80160718.
•    Install as shown in Figure 21, 22, 24B or 

25B.

•  Wire with field-sourced wiring per 

Figures 27 and 28.

Содержание Alpine ALP080B





















































































































































Отзывы: