U.S. Boiler Company Alpine ALP080B Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 148

background image

54

103448-10- 6/18

A. Installation of Factory Supplied Piping and Trim

Components

Alpine boilers have factory supplied

Miscellaneous Part Carton (P/N 102942-01

– ALP080B through ALP210B; 102942-02 or

103676-01 – ALP285B), which includes supply

piping components, gas piping components,

Temperature & Pressure Gauge, Pressure Relief

Valve and Drain Valve. See Figure 20 “Factory

Supplied Piping and Trim Installation”.

Install these components prior to connecting

boiler to system piping as follows:

VI. Water Piping and Trim

Figure 20: Factory Supplied Piping and Trim Installation

1. Relief Valve Piping, ALP080B through ALP210B

Boiler Models

a. Locate and remove ¾ in. NPT x close black

nipple, ¾ in. NPT black tee, ¾ in. MPT x

¾ in. FPT Pressure Relief Valve, ¾ in. NPT

Drain Valve.

b. Install close nipple into tee branch, then,

screw the assembly into boiler left side front

¾ in. tapping making sure tee run outlets

are in vertical plane and parallel to boiler

side.

c. Mount ¾ in. MPT x ¾ in. FPT Pressure Relief

Valve into the tee top outlet.

d. Install Drain Valve into the tee bottom outlet.

NOTICE

Failure to properly pipe boiler may result in improper operation and damage to boiler or structure.

Install boiler so that the gas ignition system components are protected from water (dripping, spraying,
rain, etc.) during appliance operation and service (circulator replacement, etc.).

Oxygen contamination of boiler water will cause corrosion of iron and steel boiler components, and can
lead to boiler failure. U.S. Boiler Company’ s Standard Warranty does not cover problems caused by
oxygen contamination of boiler water or scale (lime) build-up caused by frequent addition of water.

Do not fill boiler with softened water to prevent chloride contamination.

Installation is not complete unless a safety relief valve is installed into the tapping located on left side of
appliance or the supply piping.

«
...
52
53
54
55
56
...
»

Содержание Alpine ALP080B





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Alpine ALP080B

HI DELTA HD101 THRU 2342B

Бренд: Raypak Страницы: 4

Бренд: Raypak Страницы: 2

Бренд: Raypak Страницы: 12

Бренд: Radiant Страницы: 60

Benchmark Aerco OMM-0122

Бренд: Watts Страницы: 122

HEATNET 3.0 Torus Series

Бренд: RBI Страницы: 136

ELTHERM M Series

Бренд: green ecotherm Страницы: 34

Бренд: Ariston Страницы: 16

Бренд: REMEHA Страницы: 2

Бренд: Ponast Страницы: 59

Roca LIDIA 20 GT EM

Бренд: Baxi Страницы: 3

Бренд: Baxi Страницы: 40

Nuvola 3 BS 140 Fi

Бренд: Baxi Страницы: 224

Бренд: Sime Страницы: 100

Бренд: Viadrus Страницы: 40

Бренд: AFRISO Страницы: 2

Бренд: Ideal Boilers Страницы: 48

Бренд: Rinnai Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды