Munchkin HeatTransfer 399M Скачать руководство пользователя

Страница: 1 / 48

HEAT TRANSFER PRODUCTS, INC.

120 BRALEY RD., E. FREETOWN, MA 02717

Installing, Operating & Maintaining

MUNCHKIN HIGH EFFICIENCY HEATER

with the “925” Controller

Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified
installer, service agency or the gas supplier.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.

WARNING

This manual must only be used by a qualified heating installer / service
technician. Failure to comply could result in severe personal injury, death or
substantial property damage. It is also important to keep these Instructions
with the appliance.

MH27745

CONTROLS

Содержание HeatTransfer 399M

















































Результаты поиска

Содержание HeatTransfer 399M

Отзывы:

Похожие инструкции для HeatTransfer 399M

Бренды по названию

Популярные бренды

Munchkin HeatTransfer 399M, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание HeatTransfer 399M

Отзывы:

Похожие инструкции для HeatTransfer 399M

Бренды по названию

Популярные бренды