background image

PAGE 6 OF 17 

0921 IH-9560

OPERATION CONTINUED

TURNING ON/OFF

To turn on scale, press and hold the Zero button for 

one second. The scale performs a display test and 

momentarily displays the software version before 

entering the active weighing mode. 

To turn off the scale, press and hold the Zero button until 

OFF is displayed.

CALIBRATION OPERATION 

When the scale is operated for the first time, a span 

calibration is recommended to ensure accurate 

weighing results. Before performing the calibration, be 

sure to have the appropriate calibration weights. Ensure 

that the security switch is set to unlocked position.

Press and hold Menu until [

MENU

] is displayed. When the 

button is released, the display will show [

C.A.L

]. Press Yes 

to accept. [

SPAN

] will then be shown. Press Yes to begin 

the span calibration. 

[

--C--

] will be displayed while zero reading is stored. 

Next, the display shows the calibration weight value. 

Press the No key to toggle the value. Place the specified 

calibration weight on the pan. [

--C--

] will be displayed 

while the reading is stored. The display will show [

donE

if the calibration was successful. The scale will return to 

the previous application mode and is ready for use.

WEIGHING MODE

This mode is the factory default setting. 

1.  If needed, press and hold Mode until [

WEIGH

] is 

displayed. 

2.  If required, place an empty container on the pan 

and press Tare

3.  Add sample to the pan or container. The display will 

show the weight of the sample.

COUNTING MODE

This mode counts large numbers of items based on the 

weight of a reference count. 

1.  If required, place an empty container on the pan 

and press Tare

2.  Press and hold Mode until [

Count

] is displayed.  

[

CLr.PW

] (clear average piece weight, APW) will then 

display. If no APW exists, the scale will display [

PUt.10

], 

proceed to step 5. 

3.  Press No to use the stored APW. Proceed to step 7. 

4.  Press Yes to establish an APW. 

5.  The scale will then display the sample size, i.e.  

[

PUt 10

]. Press No or Back to toggle the choices  

(5, 10, 20, 50 or 100). 

6.  Put the indicated number of pieces on the pan and 

press Yes to calculate the APW. The display will show 

the piece count. 

7.  Add additional pieces until the desired count is 

reached. 

8.  To clear the stored APW, press and hold Mode 

until [

Count

] is displayed. Press Yes when [

Clr.pW

] is 

displayed. 

NOTE: Press Function to view the current APW.

PERCENT MODE 

This mode measures the weight of a sample as a 

percentage of a reference weight. 

1.  If required, place an empty container on the pan 

and press Tare

2.  Press and hold Mode until [

PErcnt

] is displayed.  

[

CLr.rEF

] will then display. If no reference weight 

exists, the scale will display [

Put.rEF

]; proceed to 

step 5. 

3.  Press No to use the stored reference weight and 

proceed to step 6. 

4.  Press Yes to establish a new reference. Scale will now 

display [

Put.rEF

]. 

5.  Add the desired reference material to the pan or 

container. Press Yes to store the reference weight. 

The display will show 100%. 

6.  Replace the reference material with the sample 

material. The display will show the percentage of the 

sample compared to reference weight. 

7.  To clear the stored reference, press and hold Mode 

until [

PErcnt

] is displayed. Press Yes when [

CLr.rEF

] is 

displayed. 

NOTE: Press Function to view the current 
reference weight.

CHECK MODE 

Use this mode to compare the weight to a target weight 

range. The scale supports positive, negative and zero-

check weighing. 

CHECK WEIGHING 

Use this mode to compare the weight of items to a 

target weight range. 

Содержание SCOUT H-9560


















Отзывы: