TYROLIT Hydrostress AGE230, Руководство по эксплуатации

Страница: 17 / 110

AGE230 17
TYROLIT
Attaching or changing the grinding tool
(Figure H)

Press and hold down the spindle lock ( 1. ).

Using the face spanner, loosen the clamping nut on the
spindle in an anti-clockwise direction and remove ( 2. ).

Insert the grinding wheel in the correct position.
Figure I:

Screw the clamping nut onto the spindle.
– Grinding wheel ≤ 6 mm thick:
Clamping nut collar face up, towards shaft end.
– Grinding wheel > 6 mm thick:
Clamping nut collar face down, towards gearbox.

Press and hold down the spindle lock.

Tighten the clamping nut with the face spanner.

Insert the mains plug into the socket.

Switch on the angle grinder (without locking into position)
and leave the angle grinder running for
approx. 30 seconds. Check for imbalances and vibrations!

Switch off the angle grinder.
Operating instructions
Rough-grinding
–
Angle of wheel 20–40° for best cutting performance.
–
Applying moderate pressure, move the angle grinder
backwards and forwards. As a result, the workpiece will not
become too hot and there will be no discoloration; nor will
there be any grooves.
Cut-off grinding (Figure J)
–
Hazardous quartz dust is produced when bricks, concrete
and natural stone are cut.
–
Do not press, tilt or oscillate the power tool.
–
The angle grinder must always be operated backwards,
see diagram.
Otherwise, there is a risk of the angle grinder jumping
uncontrollably out of the groove.
–
Adjust the feed to the material which is to be cut:
the harder the material, the slower the feed.
For further information on the manufacturer’s products go to
www.tyrolit.com .
Maintenance and care
Cleaning

Regularly clean the power tool and ventilation slots. Fre-
quency of cleaning is dependent on the material and dura-
tion of use.

Regularly blow out the housing interior and motor with dry
compressed air.
Carbon brushes
The angle grinder features cut-off carbon brushes.
When the wear limit of the cut-off carbon brushes is reached,
the angle grinder switches off automatically.
When the power tool is being used, the carbon brushes can be
seen sparking through the rear air inlet apertures.
If the carbon brushes spark excessively, switch off the angle grin-
der immediately.
Take the angle grinder to a customer service workshop authorised
by the manufacturer.
Gears
Repairs
Repairs may be carried out by an authorised customer service
centre only.
Spare parts and accessories
Other accessories, in particular sanding tools and cutting gu-
ards, can be found in the manufacturer's catalogues.
Exploded drawings and spare-part lists can be found on our
homepage: www.tyrolit.com
Disposal information
WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
NOTE
When the angle grinder is switched off, the grinding tool
continues running briefly.
WARNING!
Never use cutting-off wheels for rough-grinding.
WARNING!
A special cutting guard must be used for cut-off grinding.
WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
WARNING!
If metals are ground or cut over a prolonged period, conductive
dust may become deposited inside the housing. Impairment of
the protective insulation! Operate the power tool via a residual-
current-operated circuit-breaker (tripping current 30 mA).
NOTE
Use only original parts supplied by the manufacturer for
replacement purposes.
If non-original parts are used, the guarantee obligations of the
manufacturer will be deemed null and void.
NOTE
Do not loosen the screws on the gear head during the warranty
period. Non-compliance will deem the guarantee obligations of
the manufacturer null and void.
WARNING!
Render redundant power tools unusable by removing the po-
wer cord.
EU countries only
Do not throw electric power tools into the household
waste!
In accordance with the European Directive 2012/19/EU
on Waste Electrical and Electronic Equipment and
transposition into national law used electric power tools
must be collected separately and recycled in an env-
ironmentally friendly manner.
NOTE
Please ask your dealer about disposal options!