Tuthill 2002 Скачать руководство пользователя страница 27

Страница: 27 / 60

Manual 2017 Rev C p/n 2017

Installation

V-Belt Troubleshooting

PROBLEM

POSSIBLE CAUSES

SOLUTION

Belts slip (sidewalls
glazed)

Not enough tension

Replace belts; apply proper tension.

Drive squeals

Shock load

Apply proper tension.

Not enough arc of contact

Increase center distance.

Heavy starting load

Increase belt tension.

Belt(s) turned over

Broken cord caused by prying on sheave

Replace set of belts and install
correctly.

Overloaded drive

Redesign drive.

Impulse loads

Apply proper tension.

Misalignment of sheave and shaft

Re-align drive.

Worn sheave grooves

Replace sheaves.

Excessive belt vibration

Check drive design.

Check equipment for solid mounting.

Consider use of banded belts.

Mismatched belts

New belts installed with old belts

Replace belts in matched sets only.

Breakage of belt(s)

Shock loads

Apply proper tension; recheck drive.

Heavy starting loads

Apply proper tension; recheck drive.

Use compensator starting.

Belt pried over sheaves

Replace set of belts correctly.

Foreign objects in drives

Provide drive guard.

Rapid belt wear

Sheave grooves worn

Replace sheaves.

Sheave diameter too small

Redesign drive.

Mismatched belts

Replace with matched belts.

Drive overloaded

Redesign drive.

Belt slips

Increase tension.

Sheaves misaligned

Align sheaves.

Oil or heat condition

Eliminate oil. Ventilate drive.

Содержание 2002





























































Результаты поиска

Содержание 2002

Отзывы:

Похожие инструкции для 2002

Бренды по названию

Популярные бренды

Tuthill 2002, Руководство оператора

Результаты поиска

Содержание 2002

Отзывы:

Похожие инструкции для 2002

Бренды по названию

Популярные бренды