Tuthill 2002 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 60

background image

Manual 2017 Rev C p/n 2017

26

06

Operation

RECOMMENDED SHUTDOWN
PROCEDURE TO MINIMIZE RISK OF
FREEZING OR CORROSION

When an air piping system has high humidity or
moisture, water condensation can occur after
the blower is shut down and it begins to cool.
Condensation creates an environment favorable
to corrosion of the iron internal surfaces and to
ice formation in cold weather. Both conditions can
close the operating clearances, causing the blower
to fail upon future start-up.

The following shutdown procedure minimizes
the risk of moisture condensation, corrosion, and
freezing.

Care must be taken not to overload or
overheat the blower during this procedure.

1. Isolate the blower from the moist system

piping, allowing the blower to intake
atmospheric air. Operate the blower under a
slight load, allowing the blower to heat within
safe limits. The heat generated by the blower
will quickly evaporate residual moisture.

2. For carpet cleaning applications, after the

work is completed, allow the blower to run
3 – 5 minutes with the suction hose and wand
attached. The suction hose and wand will
provide enough load to the blower to evaporate
the moisture quickly.

3. For extended shutdown, inject a small amount

of a light lubricating oil such as 3-in-One® or
a spray lubricant such as WD-40® into the
inlet of the blower just before shutdown

(3-in-

One and WD-40 are registered trademarks of
WD-40 Company)

. The lubricant will provide

an excellent protective coating on the internal
surfaces. If using a spray lubricant, take care
to prevent the applicator tube from getting
sucked into the blower. The applicator tube will
damage the blower, likely to a degree where
repair would be required.

4. If the blower is being taken out of commission

for an extended period of time,

see Long-

Term Storage on page 29

.

«
...
30
31
32
33
34
...
»

Содержание 2002





























































Отзывы:

Нет отзывов

Похожие инструкции для 2002

Бренд: Walker Страницы: 40

7020-0 Snow-Bird

Бренд: Yard-Man Страницы: 12

Бренд: Zenoah Страницы: 14

Бренд: Cub Cadet Страницы: 52

Бренд: AP&T Страницы: 4

Бренд: Toro Страницы: 20

Park Ranger 2150

Бренд: Egholm Страницы: 68

Бренд: Billy Goat Страницы: 18

UltraMount MVP V-Plow Series

Бренд: Western Страницы: 92

Бренд: Snapper Страницы: 116

Бренд: Ventrac Страницы: 49

Бренд: McCulloch Страницы: 5

Бренд: Troy-Bild Страницы: 24

Бренд: Factory Catry Cat Страницы: 19

Бренд: Yardworks Страницы: 20

PTC BLOWER 950W

Бренд: RADSON Страницы: 77

Бренд: XPower Страницы: 18

Бренд: Kärcher Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды