Tuthill 2002 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 60

Tuthill 2002 Скачать руководство пользователя страница 22

Manual 2017 Rev C p/n 2017

16

05

Installation

Most CP Series blowers are shipped from
the factory in a left hand drive, vertical

À

ow

con

¿

guration. If drive shaft location is changed,

the oil level plugs, sight glasses and breathers
must be relocated to proper positions, as
shown in Figure 5-3. Failure to change plug
location will result in blower failure and void the
product warranty.

Filling Procedure

See Figure 5-3. See Recommended Lubricants
on page 42

for suggested lubricants and

grease.

1. Remove

the

¿

ll plugs or breathers from both

gear end and drive end plates.

2. Slowly pour oil through the

¿

ll until oil appears

in the oil sight glass. Bring the oil level to the
center of the sight glass.

3. Verify oil level is at proper level in both gear

end and drive end sight glasses.

4. Replace

the

¿

ll plugs or breathers that were

removed in step 1.

Figure 5-3 – Location of Oil Fill, Drain and Level Gauges on CP Series Blowers

«
...
20
21
22
23
24
...
»

Содержание 2002





























































Отзывы:

Нет отзывов