Tuthill 2002 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 60

background image

Manual 2017 Rev C p/n 2017

14

05

Installation

Soft Foot

Soft foot is a condition in which one of the blower
feet does not sit

À

at on the base. Soft foot is

usually due to irregularities in the surface to which
the blower is mounted. When the bolt on the foot
gets tightened, a slight distortion occurs that can
affect bearing and seal life as well as internal
contact between parts.

ANGULAR
SOFT FOOT

PARALLEL
SOFT FOOT

Figure 5-2 – Illustrations of Soft Foot

1. Place the blower on the base.

2. Check each foot for gaps between the foot and

base (soft foot). Shim as necessary to

¿

ll the

gap within 0.002 in. (0.05 mm).

Figure 5-2

shows the two most common types

of soft foot conditions. If either type is present
at a measurement of more than 0.003 in.
(0.076 mm), the blower may fail prematurely.

3. Tighten all bolts.

4. Mount a dial indicator on the base contacting

one foot at 12 o’clock position.

5. Loosen the bolt on that foot. Observe indicator

travel and add shims as needed to reduce
“spring” to less than 0.002 in. (0.05 mm).
Repeat steps 4 and 5 on the remaining feet.

SAFETY

Tuthill Vacuum & Blower Systems recommends
the use of relief valves to protect against excessive
pressure or vacuum conditions. Test these valves
at initial start-up to be sure they are properly
adjusted to relieve at or below the maximum
pressure differential rating of the blower.

DANGER

!

It is the responsibility of the
installer to assure that proper
guarding is in place and
compliant with all applicable
regulatory requirements.

DANGER

!

Internal and external rotating
parts of the blower and driving
equipment can produce
serious physical injuries. The
blower should never be run
with the inlet or discharge
piping removed. If it becomes
necessary to inspect the
rotating parts of the blower or
to change V-belts, be absolutely
sure that all power to the motor
controls has been shut off, the
motor controls are locked out,
and properly tagged before
proceeding.

«
...
18
19
20
21
22
...
»

Содержание 2002





























































Отзывы:

Нет отзывов

Похожие инструкции для 2002

Бренд: Yard-Man Страницы: 28

Бренд: Yard-Man Страницы: 16

Бренд: Weed Eater Страницы: 11

Бренд: Powersmart Страницы: 25

Бренд: Shindaiwa Страницы: 28

Бренд: ebm-papst Страницы: 11

Бренд: White Outdoor Страницы: 23

Бренд: WARRIOR Страницы: 61

Бренд: Hidrotermal Страницы: 4

Бренд: Troy-Bilt Страницы: 52

PPN 31A-040-401

Бренд: MTD Страницы: 2

Бренд: MTD Страницы: 28

Бренд: Worx Страницы: 12

Бренд: Poulan Pro Страницы: 9

Бренд: Poulan Pro Страницы: 10

Бренд: Poulan Pro Страницы: 13

Бренд: Poulan Pro Страницы: 40

Бренд: Sonic Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды