Tuthill 2002 Скачать руководство пользователя страница 5

Страница: 5 / 60

Manual 2017 Rev C p/n 2017

iii

Table of Contents

Disassembly and Reassembly .................................................. 30

Disassembly of Blower ....................................................................... 30

Reassembly of Blower ........................................................................ 33

Adjusting Rotor Interlobe Clearance ........................................ 36

Lubrication, Final Assembly and Mounting .............................. 37

Troubleshooting ......................................................................... 38

Assembly Clearances ................................................................ 40

Torque Chart ....................................................................................... 41

Recommended Lubricants ........................................................ 42

Recommended Lubricants for Rotary Blowers
and Vacuum Boosters ......................................................................... 42

Special Tool Drawings ............................................................... 44

Parts List ..................................................................................... 46

Cutaway Drawing for Grease Lubrication / Air Service ...................... 46

Parts List for Model CP Series – Grease Lubrication / Air Service ..... 47

Cutaway Drawing for Splash Lubrication / Air Service ....................... 48

Parts List for Model CP Series – Splash Lubrication / Air Service ...... 49

Declaration of Incorporation ..................................................... 51

Warranty – Blower Products ..................................................... 52

Operating Data Form / Product Registration ........................... 53

Содержание 2002





























































Результаты поиска

Содержание 2002

Отзывы:

Tuthill 2002, Руководство оператора, Страница: 5 / 60

Результаты поиска

Содержание 2002

Отзывы: