Turf Equipment Z-SPRAY Скачать руководство пользователя

Страница: 15 / 64

Operation

Product Overview

g313875

Figure 3

Motion control levers

Hopper

Engine/Spreader–Sprayer
Controls

Spreader impeller

Spray wand

Nozzles

Fuel cap

Spray tank

Operation

Note:

Determine the left and right sides of the

machine from the normal operating position.

Controls

Become familiar with all the controls before starting
the engine and operating the machine.

Motion Control Levers

The motion control levers, located on each side of the
top console, control the forward and reverse motion
of the machine.

Moving the levers forward or backward turns
the wheel on the same side forward or reverse
respectively. Wheel speed is proportional to the
amount the lever is moved.

g313930

Figure 4

LH Motion control lever

Forward

RH Motion control lever

Neutral

Front reference/Speed
control bar

Reverse

Front of the machine

Note:

If the motion control lever does not return

to the neutral position when released, contact an
Authorized Service Dealer.

Содержание Z-SPRAY

































































Результаты поиска

Содержание Z-SPRAY

Отзывы:

Похожие инструкции для Z-SPRAY

Бренды по названию

Популярные бренды

Turf Equipment Z-SPRAY, Руководство оператора

Результаты поиска

Содержание Z-SPRAY

Отзывы:

Похожие инструкции для Z-SPRAY

Бренды по названию

Популярные бренды