manualshive.com logo in svg

Tundra TSI308, Руководство пользователя


Поделиться
Скачать
background image

2. Interface Operation

49

Tsi308 User Manual

80D4000_MA001_02

Tundra Semiconductor Corporation

www.tundra.com

2.9.6

Secondary Bus Reset

The PCI-X bus may be placed and held in reset while the HyperTransport interface remains live. 
When the reset pin of the PCI-X bus (Px_RST_N) is asserted, all internal PCI-X buffers are 
flushed. Inbound writes that are in progress during the reset may be completed, depending on 
how far into the pipeline they are. Inbound reads are retired as their responses return from 
HyperTransport and the data dropped. Outbound operations to PCI-X are dropped and error 
status maintained and returned as if the operations had master aborted on the PCI-X bus. 
Software is responsible for coping with any transfers that were interrupted or dropped as a result 
of the reset. The interrupt controller is not affected by secondary bus reset.

2.10

 Error Handling

The Tsi308 provides a variety of error checking, logging, and containment functions to ensure 
correct operation and diagnose failures.

2.10.1

Reporting

The Tsi308 logs all errors it detects in CSRs that are persistent through a warm reset. CSR 
enables are used to mask and control routing of error notification. Not all signaling methods are 
available for all error types.

When the Tsi308 takes an error, it signals the system in one of three ways. The error-signaling 
methods are listed below in order of increasing severity:

For errors detected by the Tsi308 as a transaction target, errors may be signaled in the bridge 
chip response. The method of signaling in the response depends on the protocol of the bus on 
which the error is detected.

1.

Transaction errors on non-posted HyperTransport requests may be indicated by an Error 
response.

2.

Transaction errors on PCI may be indicated by a target abort, PERR# assertion, or 
premature disconnection before the data in error is transferred.

In each of these cases, the protocol on the given bus continues to run, and it is the requester’s 
responsibility to take appropriate action on receipt of the error. Transmission of HyperTransport 
error responses (without NXA) sets the SigdTgtAbort bit in the Status CSR. Transmission of a 
target abort on PCI sets the SigdTgtAbort bit in the Secondary Bus Status CSR.

Errors may be signaled to the system by the error interrupt pins. Two pins, FATAL_ERR_N and 
NONFATAL_ERR_N, allow division of errors into two different priority classes.

Only the Tsi308 can initiate PCI-X bus reset. The PCI-X bus is placed and held in 
reset under CSR control

Содержание TSI308





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSI308

National Instruments NI 9265 Operating Instructions Manual preview
NI 9265
Бренд: National Instruments Страницы: 26
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Бренд: National Instruments Страницы: 85
National Instruments Module SCXI-1503 User Manual preview
Module SCXI-1503
Бренд: National Instruments Страницы: 79
Patton electronics SMART NODE 4950-NCE Quick Start Manual preview
SMART NODE 4950-NCE
Бренд: Patton electronics Страницы: 8
Patton electronics NetLink 2960 RAS Datasheet preview
NetLink 2960 RAS
Бренд: Patton electronics Страницы: 2
Patton electronics 3101RC Specifications preview
3101RC
Бренд: Patton electronics Страницы: 2
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Бренд: Quantum Страницы: 20
Allied Telesis AT-9424Ts/XP AC Datasheet preview
AT-9424Ts/XP AC
Бренд: Allied Telesis Страницы: 3
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Бренд: KEMP Technologies Страницы: 71
Roland MSL-15 Owner'S Manual preview
MSL-15
Бренд: Roland Страницы: 12
H3C S10500 Series Mpls Configuration Manual preview
S10500 Series
Бренд: H3C Страницы: 400
Accom WSD/HDe Installation Procedure preview
WSD/HDe
Бренд: Accom Страницы: 15
Paradyne Hotwire 8343 Installation Instructions Manual preview
Hotwire 8343
Бренд: Paradyne Страницы: 6
SeaLevel 7205e User Manual preview
7205e
Бренд: SeaLevel Страницы: 34
ebm-papst W3G710-NK67-01 Operating Instructions Manual preview
W3G710-NK67-01
Бренд: ebm-papst Страницы: 13
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Бренд: ZALMAN Страницы: 18
Xenteq SR 200-12 User Manual preview
SR 200-12
Бренд: Xenteq Страницы: 16
Maxtor DiamondMax 8S Specification Sheet preview
DiamondMax 8S
Бренд: Maxtor Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды