manualshive.com logo in svg

Tundra TSI308, Руководство пользователя


Поделиться
Скачать
background image

2. Interface Operation

37

Tsi308 User Manual

80D4000_MA001_02

Tundra Semiconductor Corporation

www.tundra.com

•

Type 1 requests are accepted if their bus number (bits 23:16) falls within the range defined 
by the Secondary Bus Number and Subordinate Bus Number CSRs, inclusive. Type 1 
requests are routed to PCI-X, as ConfigRd or ConfigWr cycles.

A Type 1 request with a bus number that exactly matches the Secondary Bus Number CSR 
becomes a PCI-X Type 0 configuration request, with AD[device 16] set.

•

Type 1 requests with a bus number greater than Secondary Bus Number but less than or 
equal to Subordinate Bus number are passed on to PCI-X as Type 1 configuration cycles. 
Bits 23:2 of the address are left unchanged. The Tsi308 does not support the Type 1 
configuration to Special cycle mapping.

2.2.2.4

Interrupt Space

The HyperTransport specification places interrupt space in the address range of 
0000_00FD_F800_0000h to 0000_00FD_F8FF_FFFFh. The Tsi308 only accepts End of 
Interrupt (EOI) requests in this range, which should always be broadcasts. These EOI requests 
are routed to the interrupt controller.

2.2.3

HyperTransport Address Remap

Since HyperTransport technology is meant to provide a high-bandwidth backbone for I/O 
systems, which are likely to contain a variety of other buses with varying addressing 
capabilities, the HyperTransport specification defines mechanism to remap the HyperTransport 
addresses to locally defined addresses of other buses allowing mapping of the smaller address 
spaces of individual buses into different locations within the HyperTransport technology 
address map.

To support this, Tsi308 implements 64-bit Address Remapping Capability as specified in [1] 
with single upstream DMA window. This DMA window can also be used to set specific 
attributes in packets that originate on PCI-X and also fall inside the address ranges defined by 
the DMA window. An example of this attribute is that the user can program Tsi308 to set Isoc 
bit for all the packets that pass through the DMA window.

2.2.4

HyperTransport Packet Transmission

The HyperTransport packet generator logic is essentially a large arbiter/multiplexer that formats 
and combines packets from each of the three virtual channels issued from within the Tsi308. 
The output stream is combined with the stream of packets forwarded through the Tsi308 from 
the far HyperTransport link. This later multiplexing is also used to insert NOP/buffer release 
messages to the transmitter on the link’s other end.

Address Remapping is enabled through CSRs and is only applicable to packets 
traveling from/to PCI-X. It is not applicable to forward packets

Содержание TSI308





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSI308

Xinje XS Series User Manual preview
XS Series
Бренд: Xinje Страницы: 57
Caimore CM520-86EG User Manual preview
CM520-86EG
Бренд: Caimore Страницы: 79
SIIG NN-EC2812-S1 Quick Installation Manual preview
NN-EC2812-S1
Бренд: SIIG Страницы: 12
Barco ImagePRO-HD Installation Manual preview
ImagePRO-HD
Бренд: Barco Страницы: 121
WHOOP WHT-25LT Quick Start Manual preview
WHT-25LT
Бренд: WHOOP Страницы: 26
Seattle Computer Products 8086 CPU Instruction Manual preview
8086 CPU
Бренд: Seattle Computer Products Страницы: 31
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Бренд: Ubiquiti Страницы: 13
B&B Electronics EIR208 Series Quick Start Manual preview
EIR208 Series
Бренд: B&B Electronics Страницы: 2
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Бренд: Z3 Technology Страницы: 67
AXIOMTEK CEM820 Series User Manual preview
CEM820 Series
Бренд: AXIOMTEK Страницы: 58
B-G Instruments DataPlot CB1224 Manual preview
DataPlot CB1224
Бренд: B-G Instruments Страницы: 4
Disc Makers Reflex10 User Manual preview
Reflex10
Бренд: Disc Makers Страницы: 38
IBM 2740-1 System Reference Manual preview
2740-1
Бренд: IBM Страницы: 64
Datum bc635VME Operation And Technical Manual preview
bc635VME
Бренд: Datum Страницы: 49
iesy Open Standard Module RPX30 EVA-MI V1 Quick Start Manual preview
Open Standard Module RPX30 EVA-MI V1
Бренд: iesy Страницы: 9
TDK Powereta iQP Series Product Brief preview
Powereta iQP Series
Бренд: TDK Страницы: 2
Magewell XI100DUSB-SDI User Manual preview
XI100DUSB-SDI
Бренд: Magewell Страницы: 10
Z3 Technology Z3-HE2160-RPS User Instructions preview
Z3-HE2160-RPS
Бренд: Z3 Technology Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды