Tufline MVT1710 Скачать руководство пользователя страница 45

Страница: 45 / 50

Regardless of model or configuration, scrapers

are only located between two disk blades(Refer

to the diagram to the right). There is no need for

a scraper on the far outside blades on the front

gangs or the far inside blades on the rear gangs.

Optional Equipment 42

Heavy Scraper Kit Mounting Instructions

*NOTE – When attaching heavy scraper kit, do

NOT tighten any hardware until stated in direc-

tions. Adjustments may need to be made.

**NOTE – When mounting outrigger scraper

blades make sure rear scraper bar is mounted

as far to the outside as possible. This allows

outrigger scraper blade to reach outrigger disc

blade.

**NOTE – Units ordered with scraper kits as an

option will come from the manufacturer with

scraper mount brackets (Fig. 10B, Ref. 1)

installed from the factory. Units ordered without

scraper kits as an option will come from the

manufacturer with scraper spacer blocks (Fig.

10B, Ref 2) installed from the factory. If scraper

kit is ordered after original order. Remove

scraper spacer block and replace with scraper

mount brackets (Fig. 10B, Ref. 1).

Reference Figure 10

There should be a scraper mount bracket

assembled on each gang hanger. Some adjust-

ment may need to be made when mounting

scraper arm & blade assemblies (ref. #16).

Take heavy scraper bar (ref. #13) and mount on

top of scraper mount bracket assembly with

1-hole scraper bar clamp (ref. #11). Use a ½” x

2 ½” Gr. 2 bolt (ref. #6) and a ½” flange locknut

(ref. #7) to fasten. Scraper arm & blade assem-

blies (ref. #16) are now mounted on bottom of

scraper bar (ref. #13). There are two different

sides of scraper arm & blade assemblies (ref.

#16). One side fits the right front and left rear,

the other side fits the left front and right rear.

When mounting scraper arm & blade assem-

blies (ref. #16) to bottom of scraper bar (ref.

#13), use 2-hole clamp (ref. #12) on top of

scraper bar (ref. #13) and fasten together with

½” x 2 ½” Gr. 2 bolt (ref. #6) and ½” flange

locknut (ref. #7). Scraper arm & blade assem-

blies are not provided for outside front and

inside rear blades! Once all scraper arm &

blade assemblies (ref. #16) have been mount-

ed, now is the time to make adjustments to

scraper mount bracket assemblies, if needed.

When adjustments are made, tighten scraper

mount bracket assemblies to gang beam and

tighten scraper bar (ref. #13) to scraper mount

bracket assembly using 1-hole scraper bar

clamp (ref. #11) and hardware (ref. #6&7).

Scraper arm & blade assemblies (ref. #16)

should then be positioned as close to the disk

blade as possible without touching it. Turning

the gang after mounting each scraper arm &

blade assembly (ref. #16) will help determine

the correct mounting position of each one.

This is recommended to prevent dragging or

binding of the gang.

*NOTE – Tighten all fasteners after setting and

adjustments are made. Please see Bolt

Torque chart (page 45) for proper torque infor-

mation.

*NOTE – Re-tighten all fasteners after first

operational use. Please see Bolt Torque Chart

(page 45) for proper torque information.

Figure 10B

Содержание MVT1710


















































Результаты поиска

Содержание MVT1710

Отзывы:

Tufline MVT1710, Руководство оператора, Страница: 45 / 50

Результаты поиска

Содержание MVT1710

Отзывы: