Tufline MVT1710 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 50

Tufline MVT1710 Скачать руководство пользователя страница 28

Trouble Shooting 25

1. Unit not tracking or is fishtailing

2. Unit not tracking: skipping, jumping, and

fishtailing(in untilled, hard soil)

3. Unit leaving water furrow in center.

4. Unit ridging or leaving behind a high spot in

center of machine.

5. Unit leaving water furrows on outside of each

rear gang.

6. Blades plugging with soil or trash.

7. Unit leaving a balk between front inside

gangs.

8. Unit does not penetrate as desired.

A. Adjust leveling system to increase weight on

the rear of the disk and make sure the wheels

have some weight on them

B. Disk assembled incorrectly. Refer to assem-

bly instructions.

A. Level disk and make sure the wheels have

some weight on them

B. Reduce speed.

C. Reduce gang angle.

A. Disk not level. Lower rear gangs or raise

front gangs.

B. Increase speed.

C. Increase angle on rear gangs.

D. Decrease angle on front gangs.

E. Any combination of the above.

A. Disk not level. Raise rear gangs or lower

front gangs.

B. Decrease speed.

C. Decrease angle on rear gangs

D. Increase angle on front gangs.

E. Any combination of the above.

A. Add optional outrigger attachments.

A. Add optional heavy scraper kit.

If already equipped, re-adjust them.

B. Soil conditions not suitable for disking due

to excessive moisture.

A. Add optional center sweep balkbreaker

assembly.

A. Check gang angle. Increase slightly, keep-

ing front gang angle approximately 2 degrees

more aggressive than the rear.

B. Check depth control and that cylinders

retract freely.

Gang Adjustment Troubleshooting

«
...
26
27
28
29
30
...
»

Содержание MVT1710



















































Отзывы:

Нет отзывов