Tufline MVT1710 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 50

Tufline MVT1710 Скачать руководство пользователя страница 15

Dealer Instructions 12

tongue. Place the hose holder into the round

tube on side of tongue as seen in photo 17.

Remove the safety chain and safety chain bolt

from the cardboard box banded to pallet (Photo

side braces which connect the braces to frame

(Ref. 1, Photo 14). Loosen the 7/8” x 6 ½” Gr. 5

bolt which connects the tongue side braces to

the tongue (Ref. 2, Photo 14). Do not remove!

Using one of the 7/8” x 6 ½” Gr. 5 bolts removed

earlier connect the tongue to the main frame

(Ref. 1, Photo 15). Use the two 7/8” x 3 ½” Gr.

5 bolts, to connect the tongue side braces to the

frame (Ref. 2, Photo 15). Use the remaining

7/8” x 6 ½” Gr. 5 bolt to connect the rocker arm

& link bar to the frame (Ref. 3, Photo 15). Once

tongue has been connected to frame, fold the

spring rod assembly (Ref. 1, Photo 16) over to

meet the rocker arm & link bar (Ref. 2, Photo

16). Connect the two using the 5/8” x 6 ½” Gr.

2 bolt which is already in rocker arm & link bar

(Ref. 3, Photo 16). Remove the hose holder

(ref. 1, photo 17) which has been banded to the

Photo 15

Photo 16

Photo 17

Photo 18

Photo 19

Pre-Assembly cont'd on page 13

1

3

2

1

2

2

3

1

«
...
13
14
15
16
17
...
»

Содержание MVT1710



















































Отзывы:

Нет отзывов