Tufline MVT1710 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 50

Tufline MVT1710 Скачать руководство пользователя страница 30

Owner Service 27

WARNING

Lubrication(cont’d.)

on the mainframe where the gang angle turn-

buckles slide.

Lubricate the following at the end of each use

period :

• Transport wheel bearings. Pack with heavy

wheel bearing grease.
Check all gang axle nuts for proper torque peri-

odically. Please see Bolt Torque Chart (Page

45) for proper torque information.
Check gang hanger bolts periodically.Please

see Bolt Torque Chart (Page 45) for proper

torque information.

Gang Assembly for Maintenance

• When performing maintenance or repairs

make sure the equipment is in the lowered posi-

tion and both the mainframe and gangs are

properly blocked and secured to prevent rolling.

Failure to do so can cause serious injury or

death.

When gang component replacement is required,

carefully observe all safety issues. Place unit

on level ground prior to gang drop. Also make

sure that gangs are blocked to keep them from

rolling in either direction. After unit is lowered to

ground and gangs are secure, loosen nuts on

all u-bolts holding hangers to main frame

Observe the sequence and location of each

gang component and refer to the gang dia-

grams on Pages 33 and 35 for removal and

replacement of the desired component. After

replacement is completed reinstall gang parts

in proper order as shown on gang diagrams on

Pages 33 and 35. Make sure that the gang nut

on the gang axle is properly tightened after

replacements are made. Refer to Bolt Tightening

Torque Chart on (Page 45) for proper torque

information.

Storage

Lower unit for storage on level ground with

gangs resting on plyboard or other sheet mate-

rial to keep components out of the ground.

«
...
28
29
30
31
32
...
»

Содержание MVT1710



















































Отзывы:

Нет отзывов