Tufline MVT1710 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 50

Tufline MVT1710 Скачать руководство пользователя страница 19

Dealer Instructions 16

Roller Basket Assembly

Assembly

The MVT is shipped from the factory with the

roller basket assembly.

Mounting bracket, straps, arm, spring rod

assembly and hardware are assembled

together (Photo 30). Attach the mounting

bracket to the rear of the frame, with the

mounting straps, using the 5/8" x 6" bolts, lock

washers and nuts. Bracket should be 1/2" from

the inside wall of frame (Photo 31). Tighten the

top and bottom bolts evenly during this step.

Failure to do so will not allow the bracket to

Photo 30

mount properly. Next attach the arm and spring rod

assembly using the two mount pins (Photo 32).

After both sides have been mounted start assem-

bling the roller baskets together. Outer hangers are

pre assembled onto the outer end of the roller bas-

ket (Photo 33). The inner hanger or hangers are

loosly attached to the inner end of the roller basket

(Photo 34). Attach the inner ends of the roller bas-

kets together. Do this by removing the 1" lock nut

and one 1" flat washer (Photo 34, Ref. 1). Slide

baskets together and insert end of bolt into hole in

the roller basket. Put flat washer and lock nut back

onto bolt. Tighten bolt and lock nut to torq specs

(Page 45). Place tool bar onto hanger assembly.

Use 2" sq. u-bolts located on the hanger. Adjust

tool bar to the center. Roughly 2" of tool bar should

extend past outer hangers. Attach tool bar to arms.

Remove arm toolbar mount plate from arm

Photo 31

Photo 32

Photo 34

Photo 33

«
...
17
18
19
20
21
...
»

Содержание MVT1710



















































Отзывы:

Нет отзывов