Tufline MVT1710 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 50

Tufline MVT1710 Скачать руководство пользователя страница 13

Dealer Instructions 10

Pre-Assembly cont'd on page 11

band from the two remaining wheel & spindle

assemblies on pallet (Ref. 1, Photo 7). Insert

the spindle into the wheel carriage where the

wheel carriage extensions were removed. Line

up the hole in the spindle and wheel carriage

and insert the 3/8” x 3” Gr. 5 bolt removed in an

earlier step (Ref. 1, Photo 8). Repeat the same

steps for the three remaining wheels. Once

complete, tighten nuts accordingly. Please see

(Photo 3). Remove the two 7/8” x 6 ½” Gr. 5

bolts (Ref. 1 & 2, Photo 4) which connect the

tongue to the frame and pallet. Do not discard

these bolts. They will be used to connect the

tongue to the frame later in the set up. Lay the

tongue assembly (284 lbs) on the ground

(Photo 5). Using the overhead hoist, raise the

frame until pressure has been removed from

the wheels. Remove the wheel extensions (Ref.

1, Photo 6) from the wheel carriage by remov-

ing the 3/8” x 3” Gr. 5 bolt (Ref. 2, Photo 6). Do

not discard 3/8” x 3” Gr. 5 bolts, they will be

used again to reapply the wheel & spindle

assembly to wheel carriage. Also, remove the

3/8” x 3” Gr. 5 bolt holding the wheel & spindle

assembly to the wheel carriage extensions

(Ref. 3, Photo 6). Once both wheel carriage

extensions have been removed, discard both,

as they are for shipping purposes only. Cut

Photo 6

Photo 7

Photo 8

Photo 9

Photo 10

2

1

3

1

1

1

«
...
11
12
13
14
15
...
»

Содержание MVT1710



















































Отзывы:

Нет отзывов