WWW.TUCKERAUTO-MATION.COM
INSTALLATION
GUIDE
KP
evo
- TAP CONTROLLER
920.1003.02 | 12
■
PROGRAMMING INSTALLATION
ARM TYPE
Specifies the type of transmission arm installed (shoe or articulated)
START SETUP
Carries out a
Setup
cycle after confirmation.
PUSH AND GO
Sets the function that commands the automatic opening of the door
after an initial manual push:
Disabled
=
Push & Go
not enabled
Enabled
=
Push & Go
enabled
Fast food
=
Push & Go
enabled in “
FAST FOOD
“mode (manual
opening, motorised closing)
PARTIAL STOP SEC.
Specifies the detection area of the safety in opening:
Disabled
= obstacle detection active over the entire opening stroke
Enabled
= obstacle detection NOT active in proximity to the
opening stop
LEAF DELAY
Specifies the opening delay between the doors of 2 leaf models.
SCP
Specifies the function that pushes the door with a greater force in
the final section of the closure. It is useful to activate this function
if there is high friction, if the seals are particularly rigid or if locks
have a stiff latch.
Because activating the
SCP
function also reduces the
sensitivity of the electronic anti-crushing system in
the final section of closing, DO NOT activate the
SCP
function in "
low energy
" mode.
REVERSE STROKE
Sets the function that makes the door carry out a short reverse stroke
before opening to make it easier to the release the lock.
2 EASY REG.
Registration of BUS 2easy devices.
INOUT STATE
The display indicates the status (on / off) of inputs I1-I8 and outputs
O1-O2 in real-time.
DOOR STATUS
The display indicates the status of the automation in real-time.
OTHER BOARD DATA
The display indicates useful diagnostics information in real-time.
■
PROGRAMMING INTERCOM
FUNCTION
Sets the operating mode.
MASTER/SLAVE NR.
Sets the network
ID
of the unit.
INTERCOM REG.
Registers the units of the network (to be performed only on the
950N2 with
ID
1).
NODE LIST
Shows the
ID
of the units registered (on the master).
■
PROGRAMMING MISCELLANEOUS
CONFIG. DEFAULT
Shows whether the parameters have been modified, and if so, resets
the factory defaults after confirmation.
BOARD'S DISPLAY
Not active.
INTRUSION
Sets the function in which the door resists attempts to open it
manually.
KPEVO KEY
You can choose between:
Block
= the user must enter the user password in order to access
the menus that he is authorised to use.
Without user psw
= the user doesn’t need to enter the user
password in order to access the menus that he is authorised to use.
CONSECUTIVE OBST.
Specifies the maximum number of consecutive obstacle detections
in the same direction of movement, before stopping in an error
condition.
TEST ERROR
Specifies the effect that the
TEST
will have when it
detects a safety device fault:
Disabled
= the door will remain stationary in an error condition
Enabled
= the door will continue to operate at minimum speed
■
ERRORS
In this menu, the display indicates any current errors that there
may be in real time.
■
WARNINGS
In this menu, the display indicates any current alerts that there
may be in real time.
■
CYCLE COUNTER
The 950N2 has two counters:
- total, non-resettable
- partial, resettable
This menu allows you to view the cycles performed by the automa-
tion and reset the partial counter.
It is also possible to set a deadline for scheduled maintenance
according to:
- date (optional)
- number of cycles (from 1000 to 1000000)
Alert 60 will be displayed as soon as one of the two settings (date
or number of cycles) is reached.
Logging in with the user
password
only allows data
to be viewed.
■
DATE/TIME
This menu allows you to set or modify the date, time and turn
European summer time on / off.
Содержание SW10
Страница 13: ...920 1020 15 13 PUSH I O BOARD IS TOWARDS THE HINGE JAMB ...
Страница 30: ...920 1020 15 30 SIMULTANEOUS PAIRS ...
