Heat&Glo HE36CLX-S Owner'S Manual Download

Page: 1 / 59

Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14

Model: HE36CLX-S

HE36CLXLP-S

•

DO NOT

store or use gasoline or other

am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

DO NOT

try to light any appliance.

DO NOT

touch any electrical switch.

NOT

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

- If you cannot reach your gas supplier, call

the

re department.

• Installation and service must be performed

by a quali

ed installer, service agency, or the

gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a

or explosion may result causing property
damage, personal injury, or death.

Owner’s Manual

Installation and Operation

DO NOT DISCARD THIS MANUAL

NOTICE

Installation and service of this appliance should be
performed by quali

ed personnel. Hearth & Home

Technologies suggests NFI certi

ed or factory trained

professionals, or technicians supervised by an NFI
certi

ed professional.

• Leave this manual with

party responsible for use
and operation.

DO NO

DISCARD

• Important operating

and maintenance
instructions included.

• Read, understand and follow

these instructions for safe
installation and operation.

Installation and service of this appliance should be performed by a
Hearth & Home Technologies factory-trained Energy Pro technician.

WARNING

A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed.

HOT GLASS

WILL

CAUSE BURNS.

DO NOT

TOUCH GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS.

Summary of Contents for HE36CLX-S




























































Search results

Summary of Contents for HE36CLX-S

Reviews:

Related manuals for HE36CLX-S

Brands by name

Popular brands

Heat&Glo HE36CLX-S, Owner'S Manual

Search results

Summary of Contents for HE36CLX-S

Reviews:

Related manuals for HE36CLX-S

Brands by name

Popular brands