TSI Incorporated portacount pro 8030 Скачать руководство пользователя страница 67

Страница: 67 / 93

Troubleshooting 61

Symptom

Possible Causes

Solution

Suspicious

readings

(If the

ORTA

OUNT

passes the Daily

Checks, the

problem is the

respirator, not the

ORTA

OUNT

ORTA

OUNT

fit

tester is flooded with

alcohol.

Tube fittings on

ORTA

OUNT

are

loose.

P

ORTA

OUNT

leaks.

Run 2 hours to dry the

optics (remove cartridge

and install storage cap).

Tighten with pliers.

Zero-Check the

ORTA

OUNT

fit

tester and fix any leaks.

Sample lines too long.

Use standard 5-foot Twin

Tube Assembly.

Alcohol Cartridge is

loose.

Tightly close the Alcohol

Cartridge.

Respirator is not

equipped with HEPA

filters.

Install HEPA filters for fit

tests.

Twin Tube Assembly is

kinked, pinched, or

blocked.

Straighten out the Twin

Tube Assembly or

remove the obstruction.

Leaking

respirator

probe.

Tighten or seal probe.

Tubing in fit test adapter

is kinked or pinched.

Straighten out tubing.

Respirator is faulty.

Fix or replace the

respirator.

Particle count is

zero or near zero

Alcohol level is low.

Replenish alcohol.

Sampling through HEPA

Filter.

Remove filter.

Twin Tube Assembly is

blocked.

Remove the blockage.

Moisture build-up in

Alcohol Wick.

Change Alcohol Wick

inside Alcohol Cartridge.

Run 2 hours to dry optics

(remove the alcohol

cartridge and install

storage cap).

Содержание portacount pro 8030






























































































Результаты поиска

Содержание portacount pro 8030

Отзывы:

Бренды по названию

Популярные бренды

TSI Incorporated portacount pro 8030, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание portacount pro 8030

Отзывы:

Бренды по названию

Популярные бренды