TSI Incorporated portacount pro 8030 Скачать руководство пользователя страница 36

Страница: 36 / 93

30 Chapter

Insert the flash drive into one of the USB ports of the P

ORTA

OUNT

fit tester.

Press the

Database

tab.

Press

Select Database

icon.

Select the database you want to use as the active database and press

Load

When the database is loaded, select

Done

. The database you selected is

now the active database and will remain the active database until you
select another one or remove the flash drive.

Step 3—Run Daily Checks

TSI recommends maintenance checks be performed once each day before
the P

ORTA

OUNT

Respirator Fit Tester is used and whenever a

problem is encountered.

These daily checks are:

•

Particle Check

•

Classifier Check (only for the P

ORTA

OUNT

8038

with N95

enabled)

•

Zero Check

•

Max FitFactor Check

•

Valve Check (optional)

The optional valve check should be performed to help diagnose why a Max
FitFactor check failed.

Completed daily checks provide confidence that the P

ORTA

OUNT

fit

tester is working properly. Failure of any of the daily checks requires
immediate attention. See

12H

Troubleshooting

chapter. If the P

ORTA

OUNT

Respirator Fit Tester

passes the daily checks, and you have difficulty fit

testing, the problem is probably

NOT

in the P

ORTA

OUNT

fit tester.

Examine the respirator carefully for leaks or pinched tubes.

To start the daily checks:

Connect the AC Adapter to the instrument and turn on the
P

ORTA

OUNT

fit tester using the O/I button. The P

ORTA

OUNT

fit tester goes through a warm-up period before it is ready to use.

From the Activities Tab, select the Daily Checks icon [

Содержание portacount pro 8030






























































































Результаты поиска

Содержание portacount pro 8030

Отзывы:

Бренды по названию

Популярные бренды

TSI Incorporated portacount pro 8030, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание portacount pro 8030

Отзывы:

Бренды по названию

Популярные бренды