TROY XCD MAN-EXT2000 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 252

background image

3-2 Management Methods

To install XAdmin32 or XAdmin, insert the appropriate
diskette or CD-ROM in the computer, select Run from the
Windows menu, select Browse, choose the appropriate drive
(these programs are in the Utilities folder if you are using a
CD-ROM), and double click on

Setup.exe

and then click

OK.

Note

: XAdmin32 and other TROY XCD utilities are

available on the TROY XCD web site (

http://

www.troyxcd.com

) if you did not receive them on disk.

1.

Follow the instructions on the screen to complete the
installation.

2.

Double click on the XAdmin icon or use the Windows
95/NT 4.x Start button to select XAdmin in the XCD
folder in the list of Programs.

3.

A list of configured print servers will appear. If you
are running XAdmin or if you are running NetWare
with XAdmin32, skip to step 4. If you are running
TCP/IP, then you must enter an IP address into the print
server as follows (refer to Chapters 4 or 7 for alternate
methods for configuring the IP address):

-

Make sure that your computer is configured for

TCP/IP with a valid IP address configured for LAN
operation (not PPP dial-up; refer to your system
documentation for additional information).

Important Note:

Consult your system manager

before assigning IP addresses to your computer or to
the print server in order to avoid duplications. If
your network does not have an officially assigned

«
...
36
37
38
39
40
...
»

Содержание MAN-EXT2000





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAN-EXT2000

Бренд: DataCard Страницы: 7

DocuPrint C525 A

Бренд: Xerox Страницы: 49

DocuPrint C2100

Бренд: Xerox Страницы: 206

Бренд: Xerox Страницы: 116

Бренд: Xerox Страницы: 358

Бренд: Xerox Страницы: 344

Бренд: Xerox Страницы: 59

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 10

Бренд: Xerox Страницы: 51

Бренд: Xerox Страницы: 110

7300DX - Phaser Color Laser Printer

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 220

Бренд: Xerox Страницы: 28

8400B - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 203

3150 - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 2

3117 - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 8

C8 - DocuPrint Color Inkjet Printer

Бренд: Xerox Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды