manualshive.com logo in svg

TROY XCD MAN-EXT2000, Руководство администратора


Поделиться
Скачать
background image

Introduction   1-7

• More features.  Capabilities like multiple services per port,

programmable setup/reset strings, IP security, and character
substitution allow TROY XCD print servers to handle
virtually any network printing situation.

Terminology

The term "TROY XCD external print server" in this manual
covers the Pony Print Server Plus, XConnect II, XConnect 100,
and XConnect II Lite.  The term "XConnect II" is used to
represent either the XConnect II, II-LT, or II-LN03; the term
XConnect 100 means either an XConnect 100 or 100-LN03;
while the term "XConnect II  Lite" designates either an
XConnect II Lite-T or XConnect II Lite-2 .

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:  (1) This
device may not cause harmful interference and (2) this device
must accept any interference received, including interference
that may cause undesired operation.

The following information applies to the Pony Print Server Plus
(PPS-8S, PPS-8, and PPS-8N) only:

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.  These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.  This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance to the instructions, may cause harmful interference
to radio communications.  However, there is no guarantee that
interference will not occur in a particular installation.  If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the

Содержание MAN-EXT2000





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAN-EXT2000

Chamjin I&C CJ50SP User Manual preview
CJ50SP
Бренд: Chamjin I&C Страницы: 21
Xerox DocuPrint N24 Supplies Manual preview
DocuPrint N24
Бренд: Xerox Страницы: 2
Xerox Phaser 4510 Advanced Features Manual preview
Phaser 4510
Бренд: Xerox Страницы: 80
Xerox Docutech 128 Planning Manual preview
Docutech 128
Бренд: Xerox Страницы: 38
Oki C911dn Supplementary Manual preview
C911dn
Бренд: Oki Страницы: 44
Axis 570 MIO Quick Installation Manual preview
570 MIO
Бренд: Axis Страницы: 10
Zenith z-server lt User Manual preview
z-server lt
Бренд: Zenith Страницы: 218
IBM IntelliStation R Pro Hardware Maintenance Manual preview
IntelliStation R Pro
Бренд: IBM Страницы: 194
Oki PAGE 8w Lite Setup Manual preview
PAGE 8w Lite
Бренд: Oki Страницы: 18
Sun Microsystems iPlanet Web Server Installation Manual preview
iPlanet Web Server
Бренд: Sun Microsystems Страницы: 62
Xerox VersaaLink B600 User Manual preview
VersaaLink B600
Бренд: Xerox Страницы: 170
Fujitsu PRIMERGY TX2540 M1 Operating Manual preview
PRIMERGY TX2540 M1
Бренд: Fujitsu Страницы: 92
Fujitsu PRIMERGY TX200 S5 Operating Manual preview
PRIMERGY TX200 S5
Бренд: Fujitsu Страницы: 114
Fujitsu PRIMERGY TX300 S5 Options Manual preview
PRIMERGY TX300 S5
Бренд: Fujitsu Страницы: 142
Fujitsu PRIMERGY TX200 S6 Operating Manual preview
PRIMERGY TX200 S6
Бренд: Fujitsu Страницы: 126
Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual preview
Server PRIMERGY TX1330 M1
Бренд: Fujitsu Страницы: 336
Fujitsu PRIMERGY TX300 S6 Options Manual preview
PRIMERGY TX300 S6
Бренд: Fujitsu Страницы: 122
Fujitsu SE300 Operating Manual preview
SE300
Бренд: Fujitsu Страницы: 86

Бренды по названию

Популярные бренды

Загрузить еще бренды