TROY XCD MAN-EXT2000 Скачать руководство пользователя страница 211

Страница: 211 / 252

Command Summary A-9

SET BANyan [EN|DIS]

Purpose: Enables or disables Banyan protocol on print server. Banyan
is enabled by default.

SET BANyan TImeout

Sets job timeout (in seconds).

SHow BANyan

Shows Banyan protocol settings and statistics.

DLC/LLC Commands

SET DLC [EN|DIS]

Enables/disables DLC/LLC protocol

SHOw DLC [EN|DIS]

Shows DLC/LLC parameters

LAT Commands

CLear/PUrge/DELete SERVEr GRoup

number

Removes LAT group membership

SET LAT RB nn

Sets LAT receive buffer size (0-5)

SET LAT TB nn

Sets LAT transmit buffer size (0-5)

SET/DEFine/CHange SERVer GRoup mm[-nn]

Add to current LAT group membership

SET/DEFine/CHange SERVEr KEepalive nn

LAT keepalive timer (sec)

SET/DEFine/CHange SERVEr NAme <name>

Sets LAT Node name

SET/DEFine/CHange SERVEr TImeout nn

LAT inactivity timeout (sec)

Содержание MAN-EXT2000





























































































































































































































































Результаты поиска

Содержание MAN-EXT2000

Отзывы:

Похожие инструкции для MAN-EXT2000

Бренды по названию

Популярные бренды

TROY XCD MAN-EXT2000, Руководство администратора

Результаты поиска

Содержание MAN-EXT2000

Отзывы:

Похожие инструкции для MAN-EXT2000

Бренды по названию

Популярные бренды