manualshive.com logo in svg

TROY XCD MAN-EXT2000, Руководство администратора


Поделиться
Скачать
background image

14-12   Troubleshooting

SET NETWARE PASSWORD 

command) and in the file

server (using the PCONSOLE 

Print Server

Information Change Password

 command).

3. Make sure that you have enabled at least one NetWare

file server using the 

SET NETWARE SERVER 

servername

ENABLED

 command.

4. Have you exceeded your NetWare user limit?

5. If you have V3.00 or earlier firmware , make sure that

you enabled either 802.3 or Ethernet II frames on your
file server, particularly if you have a NetWare 3.12 or
4.xx file server (since these NetWare versions default to
802.2), since these versions of firmware do not support
802.2 or SNAP frames.  Also, if you are using NetWare
4.xx, make sure that you have enabled bindery emulation
on the file server.

6. Make sure that the print server name you used in

PCONSOLE exactly matches the name that is configured
in the print server, and make sure it is defined as a Queue
Server for the print queue.

7. If you are running both 802.3 and Ethernet II frames on

different file servers on your network, there is a
possibility that the print server may not make a
connection to the desired file server.  Try forcing the
frame type to the desired one using the 

SET NETWARE

FRAME

 command from the TROY XCD print server

remote console.

8. If you are losing portions of your print job and you are

using the DOS NetWare drivers, try setting the

Содержание MAN-EXT2000





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAN-EXT2000

NEC 870 - SuperScript B/W Laser Printer Network User'S Manual preview
870 - SuperScript B/W Laser Printer
Бренд: NEC Страницы: 52
NEC SuperScript 1800 Quick Start Manual preview
SuperScript 1800
Бренд: NEC Страницы: 8
NEC Express5800/320Ma Planning Manual preview
Express5800/320Ma
Бренд: NEC Страницы: 80
NEC Express5800/320Ma Technical Reference Manual preview
Express5800/320Ma
Бренд: NEC Страницы: 90
Xerox 4050 Product Reference preview
4050
Бренд: Xerox Страницы: 68
ABLE AP1200 Programmer'S Manual preview
AP1200
Бренд: ABLE Страницы: 26
Oki Okipage8z Limited Warranty preview
Okipage8z
Бренд: Oki Страницы: 16
Olivetti PR2 plus Service Manual preview
PR2 plus
Бренд: Olivetti Страницы: 179
Olivetti JS-505 Service Manual preview
JS-505
Бренд: Olivetti Страницы: 36
Oki B6200 Series Maintenance Manual preview
B6200 Series
Бренд: Oki Страницы: 679
Oki PRO511DW Manual preview
PRO511DW
Бренд: Oki Страницы: 40
OKIDATA Pacemark 3410 Service Handbook preview
Pacemark 3410
Бренд: OKIDATA Страницы: 308
OKIDATA Pacemark 3410 Instruction Manual preview
Pacemark 3410
Бренд: OKIDATA Страницы: 9
OKIDATA MICROLINE 320 Quick Manual preview
MICROLINE 320
Бренд: OKIDATA Страницы: 2
Oki Microline 8480 FB Setup Manual preview
Microline 8480 FB
Бренд: Oki Страницы: 12
Variquest Perfecta 3600STP Assembly Instructions Manual preview
Perfecta 3600STP
Бренд: Variquest Страницы: 12
Variquest Perfecta 3600STP User Manual preview
Perfecta 3600STP
Бренд: Variquest Страницы: 231
Variquest Awards Maker 400 Instructions preview
Awards Maker 400
Бренд: Variquest Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды