manualshive.com logo in svg

TROY XCD MAN-EXT2000, Руководство администратора


Поделиться
Скачать
background image

Installation   2-17

The TROY XCD print server will go through the following
startup sequence:

1. It will run through a set of power-up diagnostics for a

few seconds.  If the print server is operating properly, the
TEST LED will blink momentarily and then go out.  If
the TEST LED blinks continuously in a regular pattern,
there is a problem.  If this is the case, first verify that you
have a good Ethernet connection and then try powering the
unit off and then on again.  If the problem persists, refer to
the Troubleshooting chapter in this manual.

2. When the test LED goes out, the other LEDs on the print

server will come on as follows:

•

On the XConnect II and XConnect II Lite, the LINK
LED will blink to show activity on the network.  The
XMIT and RCV LEDs will come on solid if there is a
valid 10baseT connection (they are not used with
10base2).

•

On the XConnect 100, the Link OK LED will blink if
the print server detects activity on the network.  The
100baseTX LED will come on if a valid 100baseTX
connection is detected (this LED will not come on if
10baseT is used).

•

On the Pony 100, the Link LED will come on solid if
there is a valid 10baseT or 100baseTX connection.

•

On the Pony Print Server Plus, the LED will blink
randomly.

If the LEDs do not come on as described, there may be a
cabling problem or a bad hub port; if this is the case, try a
different cable and/or hub port.

Содержание MAN-EXT2000





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAN-EXT2000

Acer Altos R700 Series Product Manual preview
Altos R700 Series
Бренд: Acer Страницы: 80
Acer Altos G700 series Rack Installation Instructions preview
Altos G700 series
Бренд: Acer Страницы: 14
Acer Extensa 500 System Manual preview
Extensa 500
Бренд: Acer Страницы: 103
Acer Altos R720 Series Installation & Configuration Manual preview
Altos R720 Series
Бренд: Acer Страницы: 104
GCC Technologies Elite 12N Network Manual preview
Elite 12N
Бренд: GCC Technologies Страницы: 63
GCC Technologies Elite XL-1208 Supplementary Manual preview
Elite XL-1208
Бренд: GCC Technologies Страницы: 9
GCC Technologies Elite XL User Manual preview
Elite XL
Бренд: GCC Technologies Страницы: 199
Xerox DocuColor 6060 Recommended Materials List preview
DocuColor 6060
Бренд: Xerox Страницы: 4
IBM 6219 - IntelliStation M - Pro Configuration And Options Manual preview
6219 - IntelliStation M - Pro
Бренд: IBM Страницы: 317
Ricoh Aficio SP4100N-KP Specifications preview
Aficio SP4100N-KP
Бренд: Ricoh Страницы: 4
Roland VersaCamm SP-300V Manual preview
VersaCamm SP-300V
Бренд: Roland Страницы: 4
NEC SuperScript 610 User Manual preview
SuperScript 610
Бренд: NEC Страницы: 105
Ravas PR-INT-MX-RAVAS-ABLE Manual preview
PR-INT-MX-RAVAS-ABLE
Бренд: Ravas Страницы: 26
IBM xSeries 235 User Manual preview
xSeries 235
Бренд: IBM Страницы: 66
FOREVER Flex-Soft Quick Start Manual preview
Flex-Soft
Бренд: FOREVER Страницы: 2
Microcom 326M User Manual preview
326M
Бренд: Microcom Страницы: 73
Oki B4400L User Manual preview
B4400L
Бренд: Oki Страницы: 105
Jatheon PnC 100 Installation & Administrators Manual preview
PnC 100
Бренд: Jatheon Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды