background image

Instruments

87

In  the  event  of  an  incomplete  riding
mode change:

• Safely  bring  the  motorcycle  to  a

stop.

• Select neutral gear.
• Turn the ignition OFF and then back

ON again.

• Select the required riding mode.
• Restart  the  engine  and  continue

riding.

Warning

Do  not  stop  the  engine  using  the
ignition  switch  or  engine  stop  switch
whilst the motorcycle is moving.

Always  bring  the  motorcycle  to  a  stop
safely and engage neutral gear prior to
stopping the engine.

Stopping the engine by turning off the
ignition  or  engine  stop  switch  whilst
the  motorcycle  is  moving  can  lock  the
rear  wheel  causing  loss  of  motorcycle
control and an accident.

Caution

Do  not  stop  the  engine  using  the
ignition  switch  or  engine  stop  switch
whilst the motorcycle is moving.

Always  bring  the  motorcycle  to  a  stop
safely and engage neutral gear prior to
stopping the engine.

The 

transmission 

is 

pressure

lubricated  only  when  the  engine  is
running.  Inadequate  lubrication  may
cause  damage  or  seizure  of  the
transmission, which can lead to sudden
loss  of  motorcycle  control  and  an
accident.

Riding Mode Configuration

Refer to the following table for the ABS,
MAP  and  TC  options  available  for  each
riding mode.

Riding Mode

RAIN

ROAD

OFF-ROAD

ABS (Anti-lock Braking System)

Road

Off-Road

Off

MAP (Throttle Response)

Rain

Road

Off-Road

TC (Traction Control)

Rain

Road

Off-Road

Off

Key

Standard (Factory Default Setting)

Selectable Option

Option Not Available

Содержание Tiger 1200 XCA 2017











































































































































































































































Отзывы: