Triumph Adler DC 2042 Скачать руководство пользователя страница 89

Страница: 89 / 109

Replace the toner cartridge only when "ADD TONER TO RESUME COPYING" is
displayed.
* Touch the "?" key to display the toner cartridge replacement procedure on the

touch panel.

REPLACING THE TONER CARTRIDGE

1. Open the front cover. Turn the toner cartridge release lever leftward as far as it

will go. The old cartridge will be released.

2. Raise the old cartridge up slightly and pull it out towards you.

3. Hold the new cartridge horizontally, and shake it up and down 3-5 times, turning

it over each time.

4. Similarly, shake the new cartridge from side to side 5-7 times, turning it over

each time.

5. Fit the new cartridge into the copier to align the 2 arrows on new toner cartridge

and the 2 marks on the cartridge port.

6. Tip the cartridge release lever to the right. The new cartridge will be clamped.

* Check that the 2 marks on the front of the toner cartridge are aligned with the 2

marks on the cartridge port.

7. Close the front cover.

CAUTION

Do not incinerate toner and toner containers. Dangerous sparks may
cause burn.

Содержание DC 2042














































































































Результаты поиска

Содержание DC 2042

Отзывы:

Похожие инструкции для DC 2042

Бренды по названию

Популярные бренды

Triumph Adler DC 2042, Инструкция по эксплуатации

Результаты поиска

Содержание DC 2042

Отзывы:

Похожие инструкции для DC 2042

Бренды по названию

Популярные бренды