Tritech SeaHub Скачать руководство пользователя страница 47

Страница: 47 / 70

Operator Manual

Issue 1

TIL – Eng – Spec – 080

Page 47 of 70

SeaHub

7.2. Resetting the Software Default Settings

This procedure describes how to return the software settings (and hence hardware mode’s of the
communication ports) to their factory default values.

DANGER!

Before attempting this procedure ensure that the unit is disconnected from the AC
and DC power source, and all other devices be disconnected from it.

1) Follow the steps described in section 7.1 to open the

housing.

2) Locate switch block “SW1” on the PCB.

3) Using a small screw-driver, pair of tweezers or other small

pointed object to set switch 1 to the “ON” position

NB: Switch 2 will already be in the “ON” position, and should
not be changed.

4) Close the SeaHub housing, and apply power for about 10 seconds. The switch settings are only

read when the SeaHub unit powers up.

5) Disconnect from the power, re-open the housing, and set switch 1 back to the off position. If this

is not done, the unit will not be able to store any new settings.

6) Disconnect from the power again, and fully close up the SeaHub unit, reversing the steps

described in section 7.1.

When reset, the following settings should be restored

Control

Setting

Port Mode A – D

RS232

Panel LED Brightness

15 (Full) and

turned On

ArcNet receive
Source

Analogue

AVR Aux Mode

RAT

Содержание SeaHub







































































Результаты поиска

Содержание SeaHub

Отзывы:

Похожие инструкции для SeaHub

Бренды по названию

Популярные бренды

Tritech SeaHub, Руководство оператора

Результаты поиска

Содержание SeaHub

Отзывы:

Похожие инструкции для SeaHub

Бренды по названию

Популярные бренды