manualshive.com logo in svg

Tritech SeaHub, Руководство оператора

Поделиться
Скачать
Tritech SeaHub Скачать руководство пользователя страница 41

 

Operator Manual

 
  

Issue 1 

TIL – Eng – Spec – 080 

Page 41 of 70 

 

SeaHub 

6.3.2. Port B (RS232

[3]

, RS485 & RS422) 

9-Way D-Type Male connector, capable of supporting the following modes (under software selection)… 

•

  RS232 3-Wire (RX, TX, GND) 

•

 RS485 

Half 

Duplex 

•

  RS422 Full Duplex 

 
All signals are fully isolated and voltage transient with respect to the communications power supply. 
 
When used in RS232 mode, the pin out of this port is wired in the same way as a PC serial “COM” port 
(i.e. using DTE signal directions), and compatible with any standard RS232 peripherals and cabling. 
 
Hardware will support data transfer rates of up to 921,600 baud in RS232/RS485 mode. 
 

1

2

3

4

5

6

7

8

9

 

 

Connector face view

 

 

RS232 

RS485 

RS422 

1 

‡ ‡ ‡ 

2 

RX TX/RX-A TX-A 

3 

TX TX/RX-B TX-B 

4 

‡ ‡ ‡ 

5 

COMMS 

GROUND 

COMMS 

GROUND 

COMMS 

GROUND 

6 

‡ ‡ ‡ 

7 

N/A N/A RX-B 

8 

N/A N/A RX-A 

9 

‡ ‡ ‡ 

Notes: 

1)  Handshaking pins (indicated with “‡”) are internally connected together, but not used during 

operation. 

2)  The “COMMS GROUND” is isolated with respect to the other grounds (i.e. Power) described in 

other sections. All voltages on this connector are with respect to this ground 

3)  Pins 7 and 8 will have RS422 signal levels (

≈

5V) present on them when configured in RS232 or 

RS485 mode. 

4) An 

internal 

150

Ω

 termination resistor is fitted across pins 2 and 3, when in RS485/RS422 mode, 

and pins 7 and 8 permanently. 

5)  RTS and CTS handshaking protocol not available on this port. PC Serial ports should be 

configured to use no handshaking. 

 

Содержание SeaHub







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды