Tritech SeaHub Скачать руководство пользователя страница 36

Страница: 36 / 70

Operator Manual

Issue 1

TIL – Eng – Spec – 080

Page 36 of 70

SeaHub

5.3. Power Outputs

For powering external devices, the SeaHub module provides regulated power supplies from…

•

The two communication ports “C” and “D” on the rear of the unit.

(labelled in section 3.4, page 13)

•

The 4mm “DC Power Output” sockets on the rear of the unit.

•

The “AIF (ARCNET)” connector on the rear of the unit.

Different power and grounding options are available based on the users target application, but these can
be summarised by three categories…

•

Sonar Power

– “

PWR

”, derived from the AC-DC converter, or from the DC supply, depending on

which source is being used.

•

External Power

– “

EXT

”, selected by means of internal jumpers within the unit, and may be

either “PWR”, “COMM” or one of the internal is12V or +5V supplies.

•

Communications Power

– “

COMM

”, used to power all the output communications hardware.

Содержание SeaHub







































































Результаты поиска

Содержание SeaHub

Отзывы:

Похожие инструкции для SeaHub

Бренды по названию

Популярные бренды

Tritech SeaHub, Руководство оператора

Результаты поиска

Содержание SeaHub

Отзывы:

Похожие инструкции для SeaHub

Бренды по названию

Популярные бренды