manualshive.com logo in svg

Tritech SeaHub, Руководство оператора

Поделиться
Скачать
Tritech SeaHub Скачать руководство пользователя страница 46

 

Operator Manual

 
  

Issue 1 

TIL – Eng – Spec – 080 

Page 46 of 70 

 

SeaHub 

7.1. Opening the SeaHub housing 

This procedure describes how to open the SeaHub units housing, for maintenance and hardware 
configuration procedures. 
 

 

DANGER!

 

Before attempting this procedure ensure that the unit is disconnected from the AC 
and DC power source, and all other devices be disconnected from it. 

 

1)  Using a 2.5mm Hexagonal (Allen) Key to unscrew the two 

screws on the front panel of the unit (see figure below). 

 

 

NOTE

 

The two hexagonal screws on the front of the panel 
are 

NOT

 held captive, and so should be removed and 

stored prior to continuing. 

 

2)  Remove the front panel assembly from the housing. 

3)  Remove the lid of the housing, by sliding it forward out of its 

guides. 

 

 

DANGER!

 

The edges of the lid may be sharp – handle with 
care. 

 

4)  There is no need for further disassembly of the unit, as the 

circuit board and hardware jumpers are now visible. 

5)  To reassemble the unit, reverse the above steps. 

 

Содержание SeaHub







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды