manualshive.com logo in svg

Trinamic PD57-1060, Руководство по прошивке

Поделиться
Скачать
Trinamic PD57-1060 Скачать руководство пользователя страница 81

PD57/60-1060 / TMCM-1060 TMCL™ Firmware Manual (V1.04 / 2011-AUG-29) 

81 

 

 
Copyright © 2011, TRINAMIC Motion Control GmbH & Co. KG 

 

Number  Global parameter 

Description 

69 

CAN bit rate 

2 

20kBit/s 

 

3 

50kBit/s 

 

4 

100kBit/s 

 

5 

125kBit/s 

 

6 

250kBit/s 

 

7 

500kBit/s 

 

8 

1000kBit/s 

Default

 

 

70 

CAN reply ID 

The CAN ID for replies from the board (default: 2) 

71 

CAN ID 

The module (target) address for CAN (default: 1) 

73 

configuration EEPROM 
lock flag 

Write: 1234 to lock the EEPROM, 4321 to unlock it. 
Read: 1=EEPROM locked, 0=EEPROM unlocked. 

75 

telegram pause time 

Pause time before the reply via RS485 is sent.  
For RS485 it is often necessary to set it to 15 (for RS485 
adapters controlled by the RTS pin). 
For CAN interface this parameter has no effect! 

76 

serial host address 

Host  address  used  in  the  reply  telegrams  sent  back  via 
RS485. 

77 

auto start mode 

0:  Do  not  start  TMCL™  application  after  power  up 
(default). 
1: Start TMCL™ application automatically after power up. 

80 

shutdown pin 
functionality 

Select the functionality of the SHUTDOWN pin  
0 – no function 
1 – high active 
2 – low active 

81 

TMCL™ code protection  Protect  a  TMCL™  program  against  disassembling  or 

overwriting. 
0 – no protection 
1 – protection against disassembling 
2 – protection against overwriting 
3 – protection against disassembling and overwriting 

If 

you 

switch 

off 

the 

protection 

against 

disassembling,  the  program  will  be  erased  first! 
Changing this value from 1 or 3 to 0 or 2, the TMCL™ 
program will be wiped off. 

82 

CAN heartbeat 

Heartbeat  for  CAN  interface.  If  this  time  limit  is  up  and 
no  further  command  is  noticed  the  motor  will  be 
stopped.  
0 – parameter is disabled 

83 

CAN secondary address  Second CAN ID for the module. Switched off when set to 

zero. 

84 

coordinate storage 

0 – coordinates  are stored in the RAM only (but can be 
copied explicitly between RAM and EEPROM) 
1 – coordinates are always stored in the EEPROM only 

132 

tick timer 

A  32  bit  counter  that  gets  incremented  by  one  every 
millisecond. It can also be reset to any start value. 

 

 
 

 

Содержание PD57-1060


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды