8.0 Normal functioning sequence in the 4 installation modes
The EG-3 in HARDWIRE mode is always armed. When it receives a trigger from the installed hardwire control
panel, an SMS message will be sent and an alarm trigger will be sent to the indoor or outdoor wireless siren.
After this the onboard PIR sensor will become active and any violation of its protected area, the EG-3HW will
transmit the images captured, however, if after 4 min. no movement is detected, no images will be sent and the
EG-3HW onboard PIR sensor will return to standby.
The EG-3 in WIRELESS mode is armed and disarmed by the wireless control panel installed. The EG-3WL will
emit a beep when it is armed and 2 beeps when disarmed. The slave sensors installed with the “Pegaso” wire-
less control panel will trigger the panel. The panel will then trigger the EG-3WL and, if installed, also the outdoor
wireless siren. The EG-3WL will send first the personalized SMS messages to 4 memorized telephone num-
bers, then the onboard PIR will become active and if violated will transmit by MMS to the same 4 telephone
numbers and to 2 E-mail addresses the images of the protected area. After 4 min. if no movement is detected,
no images will be sent and the EG-3WL onboard PIR sensor will return to stand-by mode.
The EG-3 in STAND-ALONE mode is armed and disarmed by the keychain transmitter PEG-3. When armed,
the EG-3SL will emit 1 beep and when disarmed 2 beeps. The units onboard PIR sensor will become active af-
ter a 25 second exit time and when violated will send first the SMS trigger message and also trigger the indoor
and outdoor wireless siren followed by the images of the protected area to the memorized telephone numbers
and E-mail addresses.
The EG-3 in the STAND-ALONE MASTER mode is armed and disarmed by the keychain transmitter PEG-3.
When it is armed the unit will emit 1 beep and when disarmed 2 beeps. The EG-3SLM will become active after
a 25 second exit time and after it has receive an alarm trigger form one of the installed slave sensors, it will
send first the SMS alarm trigger message and also trigger the indoor and outdoor wireless siren and then the
EG-3SLM onboard PIR sensor will become active and, if violated, will send the MMS images to the 4 memo-
rized telephone number and E-mail addresses. After 4 min. if no movement is detected, no images will be sent
and the EG-3SLM onboard PIR sensor will return to stand-by mode.
The EG-3 will perform the following functions:
1. Sends 1 of the 3 memorized alarm trigger messages (Burglary, Fire and Panic or Medical).
2. Sends in case of a Tamper alarm trigger from any sensor an SMS message “Tamper Alarm”
3. If armed, sends, in case of a sensor with a low battery, an SMS indicating “Low Battery” of the sensor that
has transmitted the alarm trigger followed by an SMS with the alarm trigger message.
4. When the EG-3 is disarmed, if a sensor has a low battery the EG-3 will inform the end user with an SMS
“Low Battery” message. No alarm trigger will take place.
5. Sends an alarm trigger transmission to the indoor and outdoor wireless siren.
6. Sends MMS images to the memorized telephone numbers and E-mail addresses.
7. Memorize an additional 32 images on the onboard micro SD card.
8.1 Listen-in and 2 way communication functions
It is possible to operate these 2 functions only when the EG-3 is armed and only from the 1st
memorized telephone number which is considered the Master Number.
If the master number calls the EG-3, the unit will hangs up immediately, the EG-3 will call the
master number back and when the phone is answered the EG-3 will automatically go into listen-in
mode. If the master number operator chooses to go into 2 way communication, he must press the #
key on his telephone.
8.2 EG-3 real time control of the protected area
By sending simple SMS command messages, allows you to have real time control of the area you
wish to protect and at the same time allows you to change the function of how this areas must be
protected. You have also the possibility to change the state of an on-board dry contact relay that may
be use for home automation or to arm/disarm the security system (See sections 3.1 and 7.0).
Page 35
EG-3 Instruction manual
ENGLISH
