SMS command for temporary 5 second change of status of the EG-3 on board relay:
Command format: Pa B3 + #
Example: 0000B3# 0000 is the Password, B3 is the 5 second impulse command, # indicates end
of the SMS command.
On the EG-3 terminal block the terminal 6 with the terminal 7 from open will become closed for 5 se-
cond and then it will return to its original status. The terminals 6 & 8 from normally closed will
become normally open for 5 seconds and then retrun to its original status.
The EG-3 will reply with an SMS confirmation message: “RELAY ACTIVATED”
Setting the date and hour of the EG-3:
Command format: Pa dt + year/month/day, hour/minutes/s #
To change the date and hour to: 27 April 2011 hour 15:32 and 26 seconds.
Example: 0000DT2011/04/27,15:32:56# 0000 is the password, DT is the command, 2011 is the
year, 04 is the month, 27 is the day, 15 is the hour, 32 is the minutes, 56 is the seconds # indicates
end of SMS. Note: All punctuation marks seen in the above configuration must be included.
To request MMS images of the area protected by the EG-3:
Note: Images can be sent only to the telephone number memorized in the EG-3 memory.
Command format: Pa CK + number of #
Example: 0000CK3# 0000 is the Password, CK is the command, 3 is the number of images
requested, # indicates end of SMS. The EG-3 will reply by send 3 images by MMS.
To know the operation mode of the EG-3 (EG-3HW, EG-3WL, EG-3SL or EG-3SLM):
Command format: Password EG-3 + CM + #
Example: 0000CM# 0000 is the Password, CM is the command, # indicates end of SMS.
The EG-3 will send an SMS confirmation message: “EG-3HW or EG-3W or EG-3SL or EG-3SLM”
Request of EG-3 status: (This will not function in mode EG-3HW):
Command Format: Pa CC + #
Example: 0000CC# 0000 is the password, CC is the command, # indicates end of SMS.
The EG-3 will send an SMS to inform you if it is “ARM” or “DISARM”.
If this SMS message is sent while EG-3 is in EG-3HW mode, the reply will always be
“DISARMED”
The EG-3 can reply to all command messages in 3 languages: English, Italian, and Russian.
Each language will have a number (1 for English) (2 for Italian) and (3 for Russian).
To select the language that must be used by the EG-3 for the SMS replies:
Command Format: Pa LG + language #
Example: 0000LG2# 0000 is the password, LG is the command, 2 is the language (Italian)
# indicate end of SMS.
The EG-3 will send an SMS message with the language requested which in the above is
“Italian”.
The remote commands will operate only if the EG-3 is Armed and if the command is sent by
one of the 4 memorized telephone numbers.
7.2 Procedure to totally cancel the EG-3 memory
With this procedure, Tel. numbers, E-mail addresses and SMS commands will be cancelled.
1. Switch to “OFF” the “on/off” switch locate in the battery compartment.
2. Press continuously the RESET/LEARN button and turn the same switch back to “ON”.
3. Continue to press the RESET/LEARN button until 3 beeps are heard and then release.
4. Wait for a few seconds, another 2 beeps are heard. This confirms that the EG-3 memory has
been totally cleared and that he unit has been restored to original factory supply
condition.
Page 34
EG-3 Instruction manual
ENGLISH
